- 您现在的位置：买卖IC网 > PDF目录30718 > LA4550 2.1 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP12 PDF资料下载
参数资料
| 型号： | LA4550 |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 2.1 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP12 |
| 封装： | DIP-12 |
| 文件页数： | 5/9页 |
| 文件大小： | 331K |
| 代理商： | LA4550 |
LA4550
No.1718–5/9
Proper Cares in Using LA4550-Applied Set
1. If the transformer regulation is not as specified, the supply voltage drops momentarily when the motor of an AC-
powered set is turned ON. In this case, hum noise may be generated. So, be careful of the transformer regulation.
2. DC muting
To apply DC muting by controlling the NF pin, it is recommended
to use the circuit configuration shown right. The potential at point
(A) is set to 3.5 to 4V.
3. Pop noise
If pop noise generated at the time of power ON/OFF disturbs you, connect a resistor of approximately 620
across
the middle point and GND.
4. Slider contact noise of variable resistor
Since the input circuit uses PNP transistors, no input coupling capacitor is required.
However, if slider contact noise of the variable resistor presents any problem, connect a
capacitor in series with input.
Thermal Design
Since the DIP-12F package is such that the Cu-foiled area of the printed circuit board is used to dissipate heat, make the
Cu-foiled area in the vicinity of the heat sink of the IC as large as possible when designing the printed circuit board. The
use of the Cu-foiled area indicated by shading in the above-mentioned sample printed circuit pattern makes it possible
to dissipate more heat. Power dissipation Pd is increased depending on the supply voltage and load. So, it is recom-
mended to use the printed circuit board together with the heat sink. The following is a formula to be used to calculate Pd
(for stereo use). For AC power supply, however, it is recommended to actually measure Pd on the transformer of each
set. For bridge amplifier use, Pd is calculated at 1/2 of the load.
(1) DC power supply
Pd max=
+ Icco VCC (For stereo use) ..... (1)
(2) AC power supply
VCC2
: Supply voltage at quiescent mode
VCC (Pd) : Supply voltage at Pd max
VCC1
: Supply voltage at maximum output
r
: Voltage regulation VCC2 – VCC1
VCC1
Icco
: Quiescent current
Supply voltage regulation
Pd max=
+ Icco VCC (Pd) (For stereo use) .............. (2)
where
VCC (Pd)=
Example of Heat Sink Mounting Method
The heat sink must be of such a shape as to be able to dissipate heat from the IC plastic area and fin area and is soldered to
the printed circuit board as shown below. For the size of the heat sink, refer to the Pd – Ta characteristic. The material of the
heat sink is recommended to be copper or iron which is solderable. It is recommended to apply silicone grease to the IC
plastic area to reduce thermal resistance between the heat sink and the IC plastic area.
VCC2
π2R
L
VCC(Pd)2
π2R
L
(1+r) VCC1
r VCC1
√2 π R
L
RL
Po max
√
1+
×
相关PDF资料 |
PDF描述 |
|---|---|
| LA4555 | 2.3 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP12 |
| LA4557 | 2.4 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP12 |
| LA4558 | 2.4 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP12 |
| LA4571MB | 0.032 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO20 |
| LA4571MB | 0.032 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LA4555 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:2-Channel AF Power Amplifier for Radio, Tape Recorder Use |
| LA4557 | 制造商:Panasonic Industrial Company 功能描述:IC |
| LA4558 | 制造商:Panasonic Industrial Company 功能描述:IC |
| LA4560M | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| LA4570 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
发布紧急采购，3分钟左右您将得到回复。