- 您现在的位置：买卖IC网 > PDF目录32287 > LA4598 2.9 W, 2 CHANNEL, AUDIO AMPLIFIER, PZFM14 PDF资料下载
参数资料
| 型号： | LA4598 |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 2.9 W, 2 CHANNEL, AUDIO AMPLIFIER, PZFM14 |
| 封装： | SIP-14 |
| 文件页数： | 8/9页 |
| 文件大小： | 227K |
| 代理商： | LA4598 |
Features and Usage Notes
1.
VG can be lowered by adding an RNF’ to the NF pins (pins 5 and 11).
Calculated as follows:
VG = 20log Rf/(RNF +RNF’)
The IC contains Rf =20 k,RNF =62 .
However, the following must be noted:
a) If RNF’ is added, the ripple bypass effect due to the NF capacitor will worsen, resulting in a worsening of ripple
rejection.
b) Oscillation stability requires, use at 40 dB or less to be avoided.
2.
Pin 9 is intended for standby. It is used in conjunction with power supply pin 4. However, it should be noted that when
power supply pin 9 and pin 4 are used for separate systems, the output power is affected by the pin 9 supply voltage.
3.
It is recommendable to use no input capacitor. However when rubbing noise generated by the volume control is offencive to
the ear, an input capacitor must be inserted.
4.
Extreme caution must be exercised when the IC is used in the vincity of the maximum ratings, since even a slight variation
in conditions may cause the maximum ratings to be exceeded, thereby leading to breakdown.
5.
When making the board, refer to the sample printed circuit pattern. No feedback loop must be formed between input and
output. Thick and short wiring is required so that no common resistance exists between the preamplifier GND and power
amplifier GND.
6.
Addition of components as shown below enables use without introducing an increased distortion at VCC of up to
approximately 4.5 V. A capacitor of 470 F is inserted against pop noise.
Proper Cares in Mounting a Radiator Fin
1.
The tightening torque should be in a range from 4 to 6 kg.cm.
2.
The spacing between the screw holes of the radiator fin must match the spacing between the screw holes of the IC. With case
outline dimensions L and R referred to, the screws must be tightened with the distance between them as close to each other
as possible.
3.
The screws to be used must have a head equivalent to the one of truss machine screw or binder machine screw defined by
JIS. Washers must also be used to protect the IC case.
4.
No foreign matter such as cutting particles should exist between heat sink and radiator fin. When applying grease on the
junction surface, it must be applied uniformly on the whole surface.
5.
IC lead pins should be soldered to the printed circuit board after the radiator fin is mounted on the IC.
LA4598
No.4087-8/9
相关PDF资料 |
PDF描述 |
|---|---|
| LA47512 | 28 W, 4 CHANNEL, AUDIO AMPLIFIER, ZFM25 |
| LA5310M | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| LA6504H | DISK DRIVE MOTOR CONTROLLER, 1.8 A, PDSO28 |
| LA6529M | 3 CHANNEL, AUDIO AMPLIFIER, PDSO30 |
| LA6602V | SPECIALTY CONSUMER CIRCUIT, PDSO24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LA45A-2-6-BL | 制造商:Carling Technologies 功能描述:L SLIDE SWITCH - Bulk |
| LA45A-BL | 制造商:Carling Technologies 功能描述:L SLIDE SWITCH - Bulk |
| LA45B-2G-PF | 制造商:LIGITEK 制造商全称:LIGITEK electronics co., ltd. 功能描述:LED ARRAY |
| LA45B-2G-R1-PF | 制造商:LIGITEK 制造商全称:LIGITEK electronics co., ltd. 功能描述:LED ARRAY |
| LA45B-2I-R1-PF | 制造商:LIGITEK 制造商全称:LIGITEK electronics co., ltd. 功能描述:LED ARRAY |
发布紧急采购，3分钟左右您将得到回复。