- 您现在的位置：买卖IC网 > PDF目录30718 > LA4625 13.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PZFM14 PDF资料下载
参数资料
| 型号： | LA4625 |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 13.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PZFM14 |
| 封装： | SIP-14 |
| 文件页数： | 4/8页 |
| 文件大小： | 151K |
| 代理商： | LA4625 |
LA4625
No.6631-4/8
Pin Voltages
VCC = 12V, with 5V applied to STBY through a 10k resistor, RL = 4, Rg = 0
Pin No.
1
2
3
4
5
6
7
Pin name
IN1
DC
PRE-GND
STBY
ON TIME
IN2
POP
Pin voltage
1.46V
5.18V
0V
3.21V
2.26V
1.46V
2.05V
Pin No.
8
9
10
11
12
13
14
Pin name
+OUT2
OUT2
PWR-GN
+OUT1
PWR-GN
OUT1
VCC
Pin voltage
5.21V
0V
5.21V
0V
5.21V
12V
External Components
C1 and C4: Input capacitors. A value of 2.2
F is recommended. Determine the polarity based on the DC potential of
the circuit connected directly to the LA4625 front end. Note that the low band response can be adjusted by
varying fL with the capacitors C1 and C4.
C2
: Decoupling capacitor (ripple filter)
C3
: Sets the amplifier starting time, which will be approximately 0.6 seconds for a value of 33
F. The starting
time is proportional to the value of this capacitor, and can be set to any desired value.
C5
: Power-supply capacitor
C6, C7, C8, and C9 :
Oscillation prevention capacitors. Use polyester film capacitors (Mylar capacitors) with excellent
characteristics. (Note that the series resistors R2, R3, R4, and R5 are used in conjunction with these
capacitors to achieve stable amplifier operation.) A value of 0.1
F is recommended.
C10
: Impulse noise reduction capacitor. A value of 0.47
F is recommended. Caution is required when selecting
the value for this capacitor, since increasing its value influences the operation of the circuits that protect
against shorting the amplifier output pins to VCC or to ground when higher VCC voltages (approximately
16V or higher) are used.
R1
: Standby switch current limiting resistor. A value of 10k
is recommended when a voltage in the range 2.5 to
12V will be applied as the standby switching voltage. Note that this resistor is not optional: it must be included.
IC Internal Characteristics and Notes
1. Standby function
Pin 4 is the standby switch. A voltage of 2.5V or
higher must be applied through an external resistor to
turn the amplifier on.
If a voltage of over 12V will be applied as the
standby mode switching voltage, use the following
formula to determine the value of R1 so that the
current entering at pin 4 remains under 500
A.
<applied voltage> 1.4
R1 =
500
A
10k
2. Muting function
Pin 5 connects the capacitor that determines the starting time to prevent impulse noise. It can also be used to mute
the amplifier output by shorting pin 5 to ground. When this function is used, the recovery time depends on C3.
3. Impulse noise improvements
While the LA4625 achieves a low level of impulse noise, if even further reductions in impulse noise at power
on/off (and when switching into or out of standby mode) a 0.47
F capacitor may be inserted between pin 7 and the
PRE GND pin (pin 3). (Pin 7 is the output amplifier bias pin. Since the ability to withstand shorting the output pins
to VCC or ground is reduced for supply voltages over 16V if the pin 7 capacitance is large, we recommend a value
of 0.47
F or lower for this capacitor.)
4
R1
10k
500A or lower
About 1.4V
(2VBE)
Pin 4 Internal Equivalent Circuit
Applied standby
voltage
相关PDF资料 |
PDF描述 |
|---|---|
| LA4627N | 2.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP12 |
| LA4627 | 2.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP12 |
| LA4628 | 30 W, 2 CHANNEL, AUDIO AMPLIFIER, PZFM14 |
| LA4628 | 30 W, 2 CHANNEL, AUDIO AMPLIFIER, PZFM14 |
| LA4629 | 4.5 W, 2 CHANNEL, AUDIO AMPLIFIER, SFM12 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LA4625_08 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:2-channel 13.5W BTL Audio Power Amplifier |
| LA4625_10 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:2-channel 13.5W BTL Audio Power Amplifier |
| LA4625-E | 功能描述:音频放大器 2-CH POWER AMPLIFIER RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| LA4625-P-E | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| LA4627 | 制造商:Panasonic Industrial Company 功能描述:IC |
发布紧急采购，3分钟左右您将得到回复。