- 您现在的位置：买卖IC网 > PDF目录30719 > LA4663 20 W, 2 CHANNEL, AUDIO AMPLIFIER, PZFM14 PDF资料下载
参数资料
| 型号： | LA4663 |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 20 W, 2 CHANNEL, AUDIO AMPLIFIER, PZFM14 |
| 封装： | SIP-14 |
| 文件页数： | 4/10页 |
| 文件大小： | 113K |
| 代理商： | LA4663 |
Usage Notes
1. Maximum ratings
If the device is operated in the vicinity of the maximum ratings, it is possible for small changes in the operating
conditions to result in the maximum ratings being exceeded. Since this can result in destruction of the device,
applications should be designed with adequate margins in the supply voltage and other parameters so that the maximum
ratings are never exceeded during device operation.
2. Protection circuits
While the LA4663 includes a full complement of built-in protection circuits, care is required in the usage. In particular,
be careful not to short any pairs of device pins together.
[Notes on the shorting (power, ground, and load shorting) protection circuit]
This protection circuit operates whenever a power short (a short between the output and VCC), a ground short (a short
between the output and ground), or a load short (shorting between the + and – outputs) is detected. Although there are
cases where the protection circuit may not operate if the supply voltage is under 9 V, the thermal protection circuit will
protect the device in this range.
The protection circuit continues to operate during the interval that the abnormal short continues, and automatically
recovers when the error state is resolved. However, under certain usage conditions, there are situations where the
protection circuit may lock and remain locked even after the problem has been resolved. In these cases, the circuit can
be reset by switching to standby mode or turning off the power temporarily.
If the output is shorted to VCC with the IC in the standby state and furthermore, a VCC of 20 V or higher applied, an
offset will be created between the + and – outputs. If a load is connected in this state, a current will flow in that load,
and the IC may be destroyed. Applications should assure that this does not occur.
In the following situations, the operation of the protection circuit may result in a sound switching phenomenon at high
output levels. This may be a problem, depending on the details of the end product circuit itself, and must be verified in
an actual system.
At low load resistances RL (high loads) and at high VCC voltages, and with both channels operating at IO peak levels of
over 2 A per channel. (This phenomenon is more likely to occur the higher the chip temperature.)
For systems operating under the most sever conditions (high temperatures and high outputs), specific operating
conditions such that the above phenomenon does no occur are listed in the “Allowable operating supply voltage range
(VCC op)” item in the Operating Conditions section of the specifications. (Refer to the VCC op ranges for different RL
values.)
[Thermal protection circuit]
A thermal protection circuit is provided to prevent damage to or destruction of the IC itself when the IC generates
abnormally high temperatures. This means that gradual attenuation is applied to the output signals by the thermal
protection circuit if the IC junction temperature (Tj) rises above about 160°C due to insufficient heat sinking or other
problems.
3. Notes on printed circuit boards
When designing the printed circuit board pattern, keep the input lines separated from both the VCC lines and the
output lines. This is to prevent increased distortion and oscillation.
When high output levels are used, make power-ground lines as wide as possible and as short as possible to prevent the
PWR GND pins potential from increasing with respect to pre-ground. (From the standpoint of IC stability, ideally, the
ground pin potential should be the lowest potential in the system. This is to prevent trouble caused by several types of
induced parasitic devices due to increases in the GND pin potential due to the structure of the IC.)
No. 5905-3/10
LA4663
相关PDF资料 |
PDF描述 |
|---|---|
| LA4700N | 12 W, 2 CHANNEL, AUDIO AMPLIFIER, PSFM18 |
| LA4705 | 18 W, 2 CHANNEL, AUDIO AMPLIFIER, PSFM18 |
| LA4708 | 30 W, 2 CHANNEL, AUDIO AMPLIFIER, SFM18 |
| LA47202P | 29 W, 4 CHANNEL, AUDIO AMPLIFIER, ZFM25 |
| LA47202P | 29 W, 4 CHANNEL, AUDIO AMPLIFIER, ZFM25 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LA4663-B-E | 制造商:ON Semiconductor 功能描述:AUDIO AMPLIFIER BTL 2CH - Ammo Pack |
| LA4663-E | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| LA46B-DBKUG-7-PF | 制造商:LIGITEK 制造商全称:LIGITEK electronics co., ltd. 功能描述:LED ARRAY |
| LA46B-EG-4-PF | 制造商:LIGITEK 制造商全称:LIGITEK electronics co., ltd. 功能描述:LED ARRAY |
| LA46B-EG-9-PF | 制造商:LIGITEK 制造商全称:LIGITEK electronics co., ltd. 功能描述:LED ARRAY |
发布紧急采购，3分钟左右您将得到回复。