参数资料
| 型号： | LA4708N-E |
| 厂商： | ON Semiconductor |
| 文件页数： | 5/9页 |
| 文件大小： | 0K |
| 描述： | IC BTL PWR AMP 20W 2CH SIP18H |
| 标准包装： | 15 |
| 类型： | AB 类 |
| 输出类型： | 2 通道（立体声） |
| 在某负载时最大输出功率 x 通道数量： | 30W x 2 @ 2 欧姆 |
| 电源电压： | 9 V ~ 16 V |
| 特点： | 消除爆音，静音，短路和热保护，待机 |
| 安装类型： | 通孔 |
| 供应商设备封装： | 18-SIPH |
| 封装/外壳： | 18-SIP，裸露焊盘 |
| 包装： | 管件 |
LA4708N
No. A1783-5/9
Features of IC Inside and Usage Notes
Standby function
Pin 5 is the standby switch pin. The amplifier is
turned on by applying approximately 2.5V or more
to this pin through an external resistor (R1).
If voltage in excess of 13.2V is to be applied to the
standby switch, calculate the value of R1 using the
following formula so that the current flowing into
pin 5 is 500
A or less:
R1 =
10k
Mute function
Pin 6 is the connector for the capacitor that determines the on time in order to prevent pop noise. By grounding this
pin, the amplifier can implement mute operation. In this case, the recovery time depends on C3.
How to reduce pop noise
Although the LA4708N reduces pop noise, an electrolytic capacitor of between 0.47 and 2.2F can be connected
between pin 8 and the pre-GND to further reduce pop noise that occurs when power supply is turned on/off
(standby switch on/off). The larger the capacitance, the lower the frequency of pop noise, and it is barely audible,
but sound residue of the sound signal is liable to linger when power is turned off. Pin 8 is the bias pin for the output
amplifier and normally is left open.
Protectors
In an output-to-ground and output-to-VCC short protector system configuration, if a DC resistor is connected
between amplifier output pin and GND, the protector may operate, causing the amplifier not to start operating.
Therefore, as a general rule, no DC resistor should be connected between amplifier output pin and GND.
In order to prevent damage or degradation which may be caused by abnormally heated IC, the LA4708N has a thermal
shutdown protector. Accordingly, if the IC junction temperature (Tj) climbs to around 170 to 180
C due to inadequate
heat dissipation, the thermal shutdown protector will operate to control the output gradually into attenuation.
Also be fully careful of handling other protectors built in the LA4708N.
Miscellaneous
Since pins 1 and 9, which are unused, are connected internally, they must be left open.
Pin 10 is an NC pin (no internal connection).
Applied voltage
1.4V
500
A
相关PDF资料 |
PDF描述 |
|---|---|
| LDS6000NQGI | IC SENSOR TCH PURETOUCH 28VFQFPN |
| LDS6003PYGI | IC SENSOR TCH PURETOUCH 28SSOP |
| LDS6005NQGI | IC SENSOR TCH PURETOUCH 28VFQFPN |
| LDS6020PYGI | IC SENSOR TCH PURETOUCH 28SSOP |
| LDS6023NQGI | IC SENSOR TCH PURETOUCH 28VFQFPN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LA4708NF-MB-E | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| LA47201L-N-E | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| LA47201-N-E | 制造商:ON Semiconductor 功能描述:CARAUDIO AMPLIFIER BTL4CH - Ammo Pack 制造商:ON Semiconductor 功能描述:FNFLD / CARAUDIO AMPLIFIER BTL4CH |
| LA47202P | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Monolithic Linear IC Four-Channel BTL Power Amplifier for Car Audio Systems |
| LA47202P-E | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。