- 您现在的位置：买卖IC网 > PDF目录97996 > LB11600JV BRUSHLESS DC MOTOR CONTROLLER, 0.03 A, PDSO30 PDF资料下载
参数资料
| 型号： | LB11600JV |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 0.03 A, PDSO30 |
| 封装： | 0.275 INCH, SSOP-30 |
| 文件页数： | 21/30页 |
| 文件大小： | 343K |
| 代理商： | LB11600JV |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LB11600JV
No.8321-28/30
CSD voltage rise time (during motor rotation): Tchg
≈ Cc × Rc × ln((V1 - Ic × Rc) / (V2 - Ic × Rc)) (s)
Cc:
CSD pin external capacitor (connected between VCC and CSD)
Rc:
CSD pin external resistor (connected between the CSD pin and ground)
Ic:
CSD pin transistor current (3.5mA maximum (design target value))
V1:
CSD pin initial voltage
V2:
CSD pin voltage (when the transistor is in the on state): 4.9V (typical)
<Constraint Time Setting Example>
When VCC = 5V, to set the motor constraint time to 3 seconds:
Use a 10F capacitor for the CSD pin capacitor Cc and a 130k
resistor for Rc.
Motor constraint time: Tcsd = 1n (5 / (0.6 – 130k
× 1A) × 10F × 130k
= 2.36
× 10F × 130k = 3.068 (s)
The discharge time for the capacitor specified above will be the motor constraint time.
The pulse signal that detects whether or not the motor is turning is set by the CSET pin capacitor.
If a 0.022 F capacitor is used as the CSET pin capacitor Cs:
Rotation pulse signal detection time: Tps = 0.022
F × 0.7/50A = 308s
Note that care is required in setting these values since the amplitude of the rotation pulse detection signal is influenced by
the motor speed, and the CSD capacitance.
If the rotation pulse detection signal time is too short, the IC will not be able to raise the CSD potential to the high level.
Also, if the CSD pin capacitor value is too small and the discharge time too short, the rotation detection pulse signal will
not be issued for the motor rotation period at the start of motor rotation (when the motor is turning slowly), and the
constraint protection circuit may latch. For example, since at speeds under 100rpm the UH output period will be 300ms,
the motor constraint time must be set to a time of at least 600ms.
8.
Overcurrent Protection Circuit
The overcurrent protection circuit limits the output current to be a
maximum of I = VRF/Rf (where VRF = 0.24V typical, and RF is the
current detection resistor). The current limiter circuit detects the reverse
recovery current in the output diodes due to PWM operation and includes
a built-in filter circuit to prevent incorrect operation. While this internal filter circuit is adequate for most applications, if
the circuit is observed to operate incorrectly (for example, in cases where the diode reverse recovery current flows for
over 3 s), an external filter circuit (such as a passive low-pass filter circuit) must be added.
9.
Thermal Protection Circuit
The thermal protection circuit turns off one side of the output (UH, VH, and WH) if the IC junction temperature (Tj)
exceeds the stipulated temperature (TSD = 170°C, typical).
10. Direction Reversal
Do not reverse motor direction while the motor is turning. To reverse directions, first stop the motor (set PWMIN high or
set the S/S pin high) and then startup again with the desired direction.
11. HP Output
The Hall signal created from the IN3 pin Hall amplifier input signal is inverted and output from the HP pin. Since the HP
pin is an open-collector output, a pull-up resistor must be inserted between VCC and the HP pin.
Hall amplifier input conditions: IN3-: fixed potential, HP pin: pulled up to VCC.
Current
detection
resistor
To the RF pin
IN3-
IN3+ input
HP pin
相关PDF资料 |
PDF描述 |
|---|---|
| LB11690H | BRUSHLESS DC MOTOR CONTROLLER, 0.04 A, PDSO38 |
| LB11690 | BRUSHLESS DC MOTOR CONTROLLER, 0.04 A, PDIP30 |
| LB11691 | BRUSHLESS DC MOTOR CONTROLLER, 0.05 A, PDIP36 |
| LB11693JH | BRUSHLESS DC MOTOR CONTROLLER, 1.8 A, PDSO36 |
| LB11695M | BRUSHLESS DC MOTOR CONTROLLER, 0.04 A, PDSO30 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LB11600JV_11 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Brushless Motor Predriver IC for Automotive Applications |
| LB11600JV-MPB-E | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB11600JV-TLM-E | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB11620GP | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Monolithic Digital IC Brushless Motor Driver |
| LB11620GP-H | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。