- 您现在的位置：买卖IC网 > PDF目录53605 > LB11660RV BRUSHLESS DC MOTOR CONTROLLER, 1.5 A, PDSO16 PDF资料下载
参数资料
| 型号： | LB11660RV |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 1.5 A, PDSO16 |
| 封装： | 0.225 INCH, SSOP-16 |
| 文件页数： | 5/9页 |
| 文件大小： | 73K |
| 代理商： | LB11660RV |
LB11660RV
No.A0082-5/9
*1 <Power supply - GND wiring>
GRD of the IC is connected to the control circuit power supply system and GRD of the external N-channel is
connected to the motor power supply system. Groundings must be installed separately and all external control
components must be connected to the GND line of the IC.
*2 <Power stabilization capacitor for regeneration>
For the CM capacitor, that is a power stabilization capacitor for PWM drive and for absorption of kick-back, a
capacitance of 4.7
F/25V or higher must be used. The CM capacitor must be connected without fail to prevent the
IC from being damaged when power is tuned on or off.
*3 <Speed control>
1) Control voltage
The PWM duty ratio is determined by comparing the VTH pin voltage and the PWM oscillation waveforms.
When the VTH pin voltage drops, the 'ON' duty ratio increases, and when it drops to or below the PWM output L
level voltage, the duty ratio is 100%.
2) Thermistor
In thermistor applications, the 6VREG voltage is usually divided by a resistor, and the voltage thus generated is
supplied to the VTH pin.
The PWM duty ratio is varied by the changes in the VTH pin voltage which result from changes in temperature.
*4 < Setting the current limiter >
The current limiter is actuated when the voltage of the current-sensing resistors between VCC and VM increases to
0.5V or more.
Since the current of a current limiter circuit is limited by the current determined by IO = VRf/Rf (where VRf = 0.5V
typ, Rf: current-sensing resistance), the current limiter is actuated at IO = 1A when Rf = 0.5. The Rf resistor must
be connected without fail, and its constant must be within the recommended operating range for current limiters.
*5 <Hall input>
Wiring need to be short to prevent carrying of the noise. The Hall input circuit is a comparator having a hysteresis of
20mV. It is recommended that the Hall input level be more than three times (60mVp-p) this hysteresis.
*6 < PWM oscillation frequency setting capacitor >
The oscillation frequency is 23kHz when CP = 200pF and 46kHz when CP = 100pF, and this serves as the PWM
fundamental frequency.
For the most part, the PWM frequency can be obtained from the following formula:
f [kHz]
≈ (4.6×106) ÷C [pF]
*7 <RD output>
This is the open collector type output, which outputs ''L'' during rotation. It is set to 'OFF' when a lock is detected.
This output is left open when not in use.
*8 <HB pin>
This is a Hall element bias pin, that is, the 1.25V constant-voltage output pin.
*9 <RMI pin>
Lowest speed setting pin for speed control.
The minimum output duty setting is made with R3 and R4. The R4 is left open to stop operation at a duty ratio
of 0%.
相关PDF资料 |
PDF描述 |
|---|---|
| LB11683V | BRUSHLESS DC MOTOR CONTROLLER, PDSO24 |
| LB11867FV | BRUSHLESS DC MOTOR CONTROLLER, 0.02 A, PDSO16 |
| LB11983 | BRUSHLESS DC MOTOR CONTROLLER, 1 A, PDIP20 |
| LB11988HR | BRUSHLESS DC MOTOR CONTROLLER, 1.3 A, PDSO28 |
| LB11998V | BRUSHLESS DC MOTOR CONTROLLER, 1.3 A, PDSO30 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LB11660RV-MPB-E | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB11660RV-MPB-H | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB11660RV-TLM-E | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB11660RV-TLM-H | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB11668M | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:For Fan Motor Two-Phase Half-Wave Driver |
发布紧急采购，3分钟左右您将得到回复。