- 您现在的位置：买卖IC网 > PDF目录30728 > LB11692JH BRUSHLESS DC MOTOR CONTROLLER, 1.8 A, PDSO36 PDF资料下载
参数资料
| 型号： | LB11692JH |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 1.8 A, PDSO36 |
| 封装： | 0.375 INCH, HSOP-36 |
| 文件页数： | 9/12页 |
| 文件大小： | 118K |
| 代理商： | LB11692JH |
LA4814V
No.A0972-6/17
5.Second amplifier control function (only when BTL mode is used)
The second amplifier control function is a function to reduce the startup pop-noise in BTL mode. The pop noise can be
reduced by first turning on the IC while the second amplifier is stopped, then after the potential inside the IC gets
stabilized, turning on the second amplifier.
The values shown below are recommended for the control time.
C5 [
μF]
2.2
3.3
4.7
10
Twu [ms]
200
250
300
500
* Twu : Time after releasing standby to second amplifier turn-on
a) When using microcomputer control
The second amplifier can be controlled by applying the following voltages to pin 9.
Second amplifier operation mode … V9
≤ 0.3V
Second amplifier stop mode … V9
≥ 1.6V
However, set the resistance value of the resistor R6 inserted in series in such a way that the condition in the following
formula is met.
R6
≤ 16.2 × (Vcnt - 1.6) kΩ
The pin 9 injected current is expressed by the following formula :
I9 = (57.6
× Vcnt - 31.7)/(1+0.058 × R6) μA
Fig. 3
b) When microcomputer control is not possible
When the microcomputer cannot be used, the second amplifier can be controlled by adding the external components
as shown in Fig. 4.
VCC (V)
5
3.6
3
R7 (k
Ω)
10
6.8
R9 (k
Ω)
120
68
56
C8 (
μF)
100
Fig. 4
6.Shorting between pins
When power is applied with pins left short-circuited, electrical deterioration or damage may result.
Therefore, check before power application if pins are short-circuited with solder, etc. during mounting of IC.
7.Load shorting
If the load is left short-circuited for a long period of time, electrical deterioration or damage may occur.
Never allow the load to short-circuit.
8.Maximum rating
When IC is used near the maximum rating, there is a possibility that the maximum rating may be exceeded even under
the smallest change of conditions, resulting in failure. Take sufficient margin for variation of supply voltage and use IC
within a range where the maximum rating will never be exceeded.
Vcnt
CNT
R6
V9
9
+
R8
100k
Ω
R7
C8
R5
R9
VCC
CNT
STBY
14
9
8
相关PDF资料 |
PDF描述 |
|---|---|
| LB11696V | BRUSHLESS DC MOTOR CONTROLLER, 0.03 A, PDSO30 |
| LB11696V | BRUSHLESS DC MOTOR CONTROLLER, 0.03 A, PDSO30 |
| LB11824M | BRUSHLESS DC MOTOR CONTROLLER, 0.04 A, PDSO30 |
| LB11851TT | BRUSH DC MOTOR CONTROLLER, 0.02 A, PDSO10 |
| LB11921T | BRUSHLESS DC MOTOR CONTROLLER, 0.01 A, PDSO36 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LB11693 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Three-Phase Brushless Motor Driver for 24 V Fan Motors |
| LB11693H | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Monolithic Digital IC 3-Phase Brushless Motor Driver for 24V Fan Motors |
| LB11693H-MPB-E | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB11693H-TLM-E | 功能描述:马达/运动/点火控制器和驱动器 BRUSHLESS MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB11693H-TRM-E | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。