- 您现在的位置：买卖IC网 > PDF目录67755 > LB11693H BRUSHLESS DC MOTOR CONTROLLER, 1.8 A, PDSO36 PDF资料下载
参数资料
| 型号： | LB11693H |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 1.8 A, PDSO36 |
| 封装： | 0.375 INCH, SOP-44/36 |
| 文件页数： | 4/24页 |
| 文件大小： | 911K |
| 代理商： | LB11693H |
LB11693H
No.A0287-12/24
12. Undervoltage Protection Circuit
The undervoltage protection circuit turns off the low side output transistor if the LVS
pin voltage falls below the circuit's operating voltage (about 3.8V). This operating
voltage is the detection level for a 5V system. The detection level can be increased by
connecting a zener diode in series with the LVS pin to apply a level shift to the
detection level. The current flowing into the LVS pin during detection is about 65A.
To suppress variations in the zener voltage, it is necessary to stabilize the rise of the
zener diode voltage by increasing the current that flows in the zener diode. If this is
necessary, insert a resistor between the LVS pin and ground.
When the LCS pin is open, it will be pulled to the ground level by the built-in pull-down resistor and the output will be
turned off. Thus if the undervoltage protection circuit is not used, a voltage in excess of the release voltage (about 4.3V)
must be applied to the LVS pin. Note that the maximum rating for the LVS pin voltage is 30V.
13. Motor Constraint Protection Circuit
When motor motion is constrained, the external capacitor connected to the CSD pin will be alternately charged (up to
about 3.0V) with a constant current of about 2.4A and discharged with a constant current of about 0.17A (to about
1.0V). Thus the CSD pin voltage will have a sawtooth waveform. The motor constraint protection circuit turns the
motor (the low side output transistor) on or off repeatedly based on this sawtooth waveform. Motor drive will be on
during the period the CSD pin external capacitor is being charged from about 1.0V to about 3.0V and will be off when
it is being discharged from about 3.0V to about 1.0V. The drive on/off operation protects the IC and the motor when the
motor is physically constrained from moving. If a 0.47F capacitor is connected to the CSD pin, the IC will iterate an
on/off cycle in which drive is on for about 0.4 seconds and off for about 5.5 seconds.
While the motor is turning, the CSD pin voltage will be held at a certain voltage (that depends on the motor speed) by
(a) a CSD pin external capacitor discharge operation based on about 10s discharge pulses generated internally in the
IC when the Hall input IN1 switches (that is, on rising and falling edges on the FG output) and (b) a charge operation on
that capacitor by a constant current of about 2.4A.
Since the Hall input IN1 does not switch when the motor is physically constrained, the discharge pulses are not
generated and the CSD pin external capacitor will be charged to about 3.0V by the constant current of about 2.4A. The
motor constraint protection circuit operates when the capacitor reaches about 3.0V. The constraint protection operation
will be released when the motor constraint is released.
If the motor speed is extremely low, the CSD pin voltage during that motor rotation will be held at a comparatively high
voltage, and if that voltage reaches about 3.0V, the constraint protection function will operate. Since the constraint
protection function will operate if the Hall input IN1 frequency falls below about 10Hz, caution is required when using
the motor constraint protection circuit with motors that will operate at low speeds.
Connect the CSD pin to ground if the motor constraint protection circuit is not used.
相关PDF资料 |
PDF描述 |
|---|---|
| LB11693JH | BRUSHLESS DC MOTOR CONTROLLER, 1.8 A, PDSO36 |
| LB11693 | BRUSHLESS DC MOTOR CONTROLLER, 1.8 A, PDFM28 |
| LB11873 | BRUSHLESS DC MOTOR CONTROLLER, 1.8 A, PDSO36 |
| LB11873 | BRUSHLESS DC MOTOR CONTROLLER, 1.8 A, PDSO36 |
| LB11922 | BRUSHLESS DC MOTOR CONTROLLER, 0.03 A, PDSO36 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LB11693H-MPB-E | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB11693H-TLM-E | 功能描述:马达/运动/点火控制器和驱动器 BRUSHLESS MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB11693H-TRM-E | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB11693JH | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Monolithic Digital IC 24V Fan Motor Driver IC |
| LB11693JH_10 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:24V Fan Motor Driver IC |
发布紧急采购，3分钟左右您将得到回复。