- 您现在的位置：买卖IC网 > PDF目录67755 > LB11693JH BRUSHLESS DC MOTOR CONTROLLER, 1.8 A, PDSO36 PDF资料下载
参数资料
| 型号： | LB11693JH |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 1.8 A, PDSO36 |
| 封装： | 0.375 INCH, HSOP-36 |
| 文件页数： | 2/12页 |
| 文件大小： | 119K |
| 代理商： | LB11693JH |
LB11693JH
No.A0606-10/12
8. Forward/Reverse Switching
The LB11693JH was designed assuming that forward/reverse switching would not be performed while the motor is
operating. We recommend that the F/R pin be held fixed at either the low (forward) or high (reverse) level when the
motor is turning. Although it will be pulled up to the high level by an internal pull-up resistor (about 40k
) when left
open, this must be strengthened by an external resistor if fluctuations are large.
If the direction is switched while the motor is turning, large currents will flow due to the braking operation. The
LB11693JH's current limiter circuit, however, cannot limit this braking current. Therefore, forward/reverse switching
during motor rotation is only possible if the braking current is limited to a value under IO max (1.8A) by the motor
coil resistance or other circuit or phenomenon. Furthermore, since through current will flow in the high and low side
transistors at the instant the switch occurs with switching that only uses the F/R pin, applications must provide a rive
off period for switching directions. A drive off period must be provided by either setting the IC to the stopped state
with the S/S pin or setting the PWM signal to the 0% duty state with the TOC and PWMIN pins, and the F/R pin
must only be switched during that period to prevent through current.
9. Power Saving Circuit
This IC can be set to a power saving state in which current consumption is reduced by setting it to the stopped state
with the S/S pin. The bias current to most of the circuits in the IC is cut off in this power saving state. Note, however,
that the 5V regulator output is still provided in the power saving state.
10. Notes on the PWM Frequency
The PWM frequency is determined by the capacitance (F) of the capacitor connected to the PWM pin.
fPWM
≈1/ (23400×C)
A frequency in the range 15 to 25kHz is desirable for the PWM frequency. The ground side of the connected
capacitor must be connected to the GND1 pin by as short a line as possible.
11. Control Methods
The output duty can be controlled by either of the following methods.
Comparison of the TOC pin voltage with the PWM oscillator waveform
This method determines the low side output transistor duty according to the result of comparing the TOC pin
voltage with the PWM oscillator waveform. The PWM duty will be 0% when the TOC pin voltage is under about
1.3V and will be 100% when that voltage is over about 3.0V.
Since the TOC pin is the output of the CTL amplifier, a control voltage cannot be directly input to the TOC pin.
Accordingly, the CTL amplifier is normally used as a full feedback amplifier (by connecting the EI- pin to the
TOC pin) and inputting a DC voltage to the EI pin (here the TOC voltage will be equal to the EI+ pin voltage).
When the EI+ pin voltage increases, the output duty will increase as well. Since the motor will be driven if the EI+
pin is in the open state, a pull-down resistor should be connected to the EI+ pin in applications where this is not
desirable.
A low level must be input to the PWMIN pin (or it must be connected to ground) if the TOC pin voltage control
system is used.
PWMIN pulse input
A 15 to 25kHz frequency pulse signal can be input to the PWMIN pin and the low side output transistor duty can
be controlled based on the duty of that input signal. When the PWMIN pin is low, the output will be on, and when
high, the output will be off. When the PWMIN pin is open, the input will go to the high level and the output will be
off.
If PWMIN pin control is used, the EI- pin must be connected to ground and the EI+ pin must be connected to the
TOC pin.
相关PDF资料 |
PDF描述 |
|---|---|
| LB11693 | BRUSHLESS DC MOTOR CONTROLLER, 1.8 A, PDFM28 |
| LB11873 | BRUSHLESS DC MOTOR CONTROLLER, 1.8 A, PDSO36 |
| LB11873 | BRUSHLESS DC MOTOR CONTROLLER, 1.8 A, PDSO36 |
| LB11922 | BRUSHLESS DC MOTOR CONTROLLER, 0.03 A, PDSO36 |
| LB11922 | BRUSHLESS DC MOTOR CONTROLLER, 0.03 A, PDSO36 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LB11693JH_10 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:24V Fan Motor Driver IC |
| LB11693JH-MPB-E | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB11693JH-TLM-E | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB11695M-TLM-E | 制造商:Sony Semiconductor Solutions Division 功能描述: |
| LB11696V | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Direct PWM Drive Brushless Motor Predriver IC |
发布紧急采购，3分钟左右您将得到回复。