- 您现在的位置：买卖IC网 > PDF目录53605 > LB11867FV BRUSHLESS DC MOTOR CONTROLLER, 0.02 A, PDSO16 PDF资料下载
参数资料
| 型号： | LB11867FV |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 0.02 A, PDSO16 |
| 封装： | 0.225 INCH, SSOP-16 |
| 文件页数： | 6/9页 |
| 文件大小： | 90K |
| 代理商： | LB11867FV |
LB11867FV
No.A0195-6/9
*6. RMI pin
Minimum speed setting pin.
Perform pull-up with 5VREG when this pin is not to be used.
If the IC power supply is likely to be turned OFF first when the pin is used with external power supply, be sure to
insert the current limiting resistor to prevent inflow of large current. (The same applies to the VTH pin.)
*7. VTH pin
Speed control pin.
Connect this pin to GND when it is not used (at full speed).
For the control method, refer to the timing chart.
For control with pulse input, insert the current limiting resistor and use the pin with the frequency of 20k to 100kHz
(20kHz to 50kHz recommended).
*8. SENSE pin
Current limiting detection pin.
When the pin voltage exceeds 0.2V, the current is limited and the operation enters the lower regeneration mode.
Connect this pin to GND when it is not to be used.
*9. FG pin
Rotation speed detection pin.
This is an open collector output, which can detect the rotation speed from the FG output according to the phase
changeover. Keep this pin open when it is not to be used.
*10. CT pin
Pin to connect the lock detection capacitor.
The constant-current charge and discharge circuits incorporated cause locking when the pin voltage becomes 3.0V
and unlocking when it is 1.1V.
Connect the pin to GND when it is not to be used (locking not necessary).
*11. S-S pin
Pin to connect the soft-start setting capacitor.
Connect the capacitor between 5VREG and S-S pin.
This pin enables setting of the soft start time according to the capacity of the capacitor.
See the timing char.
Connect the pin to GND when it is not to be used.
相关PDF资料 |
PDF描述 |
|---|---|
| LB11983 | BRUSHLESS DC MOTOR CONTROLLER, 1 A, PDIP20 |
| LB11988HR | BRUSHLESS DC MOTOR CONTROLLER, 1.3 A, PDSO28 |
| LB11998V | BRUSHLESS DC MOTOR CONTROLLER, 1.3 A, PDSO30 |
| LB1617M | BRUSHLESS DC MOTOR CONTROLLER, 1.5 A, PDSO30 |
| LB1649 | BRUSH DC MOTOR CONTROLLER, 1 A, PDIP12 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LB11867FV_11 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:For Fan Motor Variable Speed Single-phase Full-wave Pre-driver |
| LB11867FVL-MPB-E | 制造商:ON Semiconductor 功能描述:SINGLE PHASE MOTOR DRIVER - Ammo Pack |
| LB11867FVL-TLM-E | 制造商:ON Semiconductor 功能描述:SINGLE PHASE MOTOR DRIVER - Tape and Reel |
| LB11867FV-MPB-E | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB11867FV-MPB-H | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。