- 您现在的位置：买卖IC网 > PDF目录97997 > LB11948T STEPPER MOTOR CONTROLLER, 0.5 A, PDSO30 PDF资料下载
参数资料
| 型号： | LB11948T |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 0.5 A, PDSO30 |
| 封装： | 0.275 INCH, TSSOP-30 |
| 文件页数： | 8/13页 |
| 文件大小： | 161K |
| 代理商： | LB11948T |
LB11948T
No.7947-4/13
Pin Functions
Pin No.
Pin Name
Description
1
OUT1-
Output
2
OUT1
Output
3
NC
Unused
4
NC
Unused
5
D-GND
Lower side internal diode anode connection
6
E1
Constant current control sensing
The motor current is set by the value of the sensing resistor Re connected between the E1 pin and ground.
The current is set according to the following equation : IO = VREF/Re (A)
7
VS1
VS power supply
8
NC
Unused
9
VCC
VCC power supply
10
CR
RC oscillator connection
11
VREF1
Current setting system reference voltage input
VREF1 voltage range : 0 to 0.5V
12
NC
Unused
13
ENABLE1
Output is turned on when ENABLE1 is low, and the output is turned off (operating state) when ENABLE1 is high.
14
PHASE1
Logic level input : phase switching
When PHASE1 = high : Output pin states : OUT1 : high, OUT1- : low.
When PHASE1 = low : Output pin states : OUT1 : low, OUT1- : high.
15
ST
Standby mode setting
When ST = high : the IC operates in normal operating mode.
When ST = low : the IC operates in standby mode. The VS and VCC current drain levels are under 1μA in this mode.
16
NC
Unused
17
1VREG
1V regulator circuit output
The LB11948 includes an internal 1V regulator circuit, and this pin is the output from that circuit. The VREF1 and VREF2
reference voltages can be set by voltage dividing the 1V regulator output.
18
PHASE2
Logic level input : phase switching
When PHASE2 = high : Output pin states : OUT2 : high, OUT2- : low.
When PHASE2 = low : Output pin states : OUT2 : low, OUT2- : high.
19
ENABLE2
Output is turned on when ENABLE2 is low, and the output is turned off (operating state) when ENABLE2 is high.
20
VREF2
Current setting reference voltage input
VREF2 voltage range : 0 to 0.5V
21
GND
Ground (small signal circuit system ground)
22
PGND
Power system ground (high current circuit system ground)
23
NC
Unused
24
VS2
VS power supply
25
E2
Constant current control sensing
The motor current is set by the value of the sensing resistor Re connected between the E2 pin and ground.
The current is set according to the following equation : IO = VREF/Re (A)
26
D-GND2
Lower side internal diode anode connection
27
NC
Unused
28
NC
Unused
29
OUT2
Output
30
OUT2-
Output
相关PDF资料 |
PDF描述 |
|---|---|
| LB1814M | DISK DRIVE MOTOR CONTROLLER, 1 A, PDSO36 |
| LB1821M | BRUSHLESS DC MOTOR CONTROLLER, 0.03 A, PQFP44 |
| LB1823M | BRUSHLESS DC MOTOR CONTROLLER, 0.03 A, PDSO30 |
| LB1875 | BRUSHLESS DC MOTOR CONTROLLER, 0.03 A, PDSO36 |
| LB1897H | BRUSHLESS DC MOTOR CONTROLLER, PDSO34 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LB11948T_07 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:PWM Constant Current Control 1-2 Phase Excitation Stepping Motor Driver |
| LB11948T_10 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:PWM Constant Current Control 1-2 Phase Excitation Stepping Motor Driver |
| LB11948T-MPB-E | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB11948T-TLM-E | 功能描述:马达/运动/点火控制器和驱动器 PRINTER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB-1195 | 制造商:Ideal Industries Inc 功能描述:WIRESTOP STMLT STD 制造商:Ideal Industries Inc 功能描述:Stripmaster Lite Repair |
发布紧急采购，3分钟左右您将得到回复。