- 您现在的位置：买卖IC网 > PDF目录65794 > LB11970FV (SANYO SEMICONDUCTOR CO LTD) BRUSHLESS DC MOTOR CONTROLLER, 1.2 A, PDSO18 PDF资料下载
参数资料
| 型号： | LB11970FV |
| 厂商： | SANYO SEMICONDUCTOR CO LTD |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 1.2 A, PDSO18 |
| 封装： | 0.225 INCH, SSOP-18 |
| 文件页数： | 6/7页 |
| 文件大小： | 69K |
| 代理商： | LB11970FV |
LB11970FV
No.A0707-6/7
*1. Power supply - GND wiring
PGND is connected to the motor power system while SGND is connected to the control circuit power system.
Wiring is made separately for PGND and SGND, and external parts of each control system are connected to SGND.
*2. Power stabilization capacitor for regeneration
CM capacitor is a power stabilizing capacitor for PWM drive and kick-back absorption and has the capacitance of
4.7
F or more. Since this IC performs current regeneration with the lower Tr through switching of the upper Tr,
connect CM with the thick and shortest possible pattern between VM and PGND.
*3. Setting of the temperature detection variable speed
Setting of the triangular wave oscillation voltage
The rotation speed variable range for the temperature is set with the triangular wave oscillation voltage.
There are two setting methods as follows:
3-1
The upper voltage (VCPH) of triangular wave is determined by V[voltage of the R1 connection counterpart]
×
(R2/(R1+R2)) and the lower voltage (VCPL) of triangular wave is determined by V
× ((R2//R3) / (R1+R2//R3)).
3-2
The upper voltage (VCPH) of triangular wave is determined by V
× ((R2+R3) / (R1+R2+R3)) and the lower voltage
(VCPL) of triangular wave is determined by V
× (R2/(R1+R2)).
Setting of the thermistor
The resistance (RTU from VCC or 6VREG and the voltage generated through division of thermistor (TH) are input
in the VTH pin. When the voltage at the VTH pin drops below VCPL due to temperature change, the full speed
(thermistor input speed control side only) is obtained.
To set the full speed with the thermistor tripping, connect each pin of 3-3 to VCC and each input voltage is
generated by divided resistance from VCC. When the thermistor trips and the VTH pin is pulled up to VCC, the full
speed (thermistor input speed control side only) is obtained.
*4. Setting the current limiter
The current limiter is activated when the voltage between current detection resistors exceeds 0.48V between VCC and
VM.
The current limiter is activated at IO = 480mA when RL = 1. Setting is made with the Rf resistance.
Short-circuit VCC and VM when the current limiter is not to be used.
When 12V is used, the current limiter must be applied at 1A or less if the coil resistance is 10
or less.
*5. Hall input
Wiring must be as short as possible to prevent carrying of noise. The Hall input circuit is a comparator with
hysteresis of 20mV. The Hall input level is recommended to be three times (60mVp-p) or more of this hysteresis.
*6. Capacitor to set the PWM oscillation frequency
Oscillation with f = 25kHz occurs at CP = 100pF and PWM voltage width of 1.6V, and becomes the reference
frequency of PWM.
*7. FG output
This is the open collector output, enabling detection of the rotation speed using the FG output corresponding to the
phase shift. Keep this output OPEN when not used.
*8. HB pin
Hall element bias pin, which is a 1.22V constant-voltage output pin
*9. RMI pin
Minimum speed setting pin for thermistor speed control, which must be pulled up with 6 VREG when not used.
By connecting the capacitor, the time to ignore thermistor input at startup can be set.
*10. PIN pin
Direct PWM speed control pin. Pull down the P-IN input to GND when not using this pin.
The lowest output DUTY setting is made with R4 and R5. Keep R5 open for stop with DUTY at 0%.
相关PDF资料 |
PDF描述 |
|---|---|
| LB11970FV | BRUSHLESS DC MOTOR CONTROLLER, 1.2 A, PDSO18 |
| LB11981 | BRUSHLESS DC MOTOR CONTROLLER, 1 A, PDSO28 |
| LB11988N | AC MOTOR CONTROLLER, 1.3 A, PDIP18 |
| LB11997H | DISK DRIVE MOTOR CONTROLLER, 1.3 A, PDSO28 |
| LB1256M | SPECIALTY ANALOG CIRCUIT, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LB11970FV-MPB-E | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB11970FV-MPB-H | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB11970FV-TLM-E | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB11970FV-TLM-H | 功能描述:马达/运动/点火控制器和驱动器 BRUSHLESS MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB11970FV-W-AH | 制造商:ON Semiconductor 功能描述:SINGLE PHASE MOTOR DRIVER - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。