- 您现在的位置：买卖IC网 > PDF目录39188 > LB1836M (SANYO SEMICONDUCTOR CO LTD) SPECIALTY ANALOG CIRCUIT, PDSO14 PDF资料下载
参数资料
| 型号： | LB1836M |
| 厂商： | SANYO SEMICONDUCTOR CO LTD |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO14 |
| 封装： | MFP14S |
| 文件页数： | 4/6页 |
| 文件大小： | 81K |
| 代理商： | LB1836M |
LB1836M
No.3947-4/6
Design Notes
If large current flows on the power supply (VS) line and the GND line, then in some applications and layouts,
misoperation due to line oscillation may result.
The modes during which large current flows are as follows :
Motor surge current when the DC motor starts up or when it shifts rotation directions (forward reverse).
Passthrough current generated within the IC when shifting rotation directions (forward reverse) or when shifting
from forward/reverse rotation to braking, or vice versa.
The following points should be kept in mind regarding the pattern layout :
Keep the wiring lines thick and short in order to reduce wiring inductance between the power supply (VS) and GND.
Insert a passthrough capacitor near the IC. (Maximum effect is obtained by inserting the passthrough capacitor
between VS and the pin 7 GND at the closest distance possible.
If the CPU and the LB1836M are mounted on separate boards and the difference between the ground potential of each
board is large, install resistors of about 10k
in series between the CPU and the LB1836M inputs.
Vcont pin
ID =
VZ
r
(= constant)
As shown in the above diagram, the Vcont pin outputs the voltage of the band gap Zener VZ + VF (=1.93V).
In normal use, this pin is left open.
The drive current ID is varied by the Vcont voltage. However, because the band gap Zener is shared, it functions as a
bridge.
M
OUT
300
OUT
ID
IN
VCC
Vcont
VZ
VS
相关PDF资料 |
PDF描述 |
|---|---|
| LB1837M | SPECIALTY ANALOG CIRCUIT, PDSO14 |
| LB1845 | STEPPER MOTOR CONTROLLER, 1.75 A, PDFM28 |
| LB1845 | STEPPER MOTOR CONTROLLER, 1.75 A, PDFM28 |
| LB1846M | STEPPER MOTOR CONTROLLER, PDSO10 |
| LB1848M | STEPPER MOTOR CONTROLLER, 0.8 A, PDSO10 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LB1836M_10 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Low-Saturation Bidirectional Motor Driver for Low-Voltage Drive |
| LB1836M_12 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Low-Saturation Bidirectional Motor Driver for Low-Voltage Drive |
| LB1836MEVB | 功能描述:电源管理IC开发工具 EVM FOR LB1836M RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| LB1836ML-MPB-E | 制造商:ON Semiconductor 功能描述:H-BRIDGE MOTOR DRIVER - Ammo Pack |
| LB1836ML-TLM-E | 功能描述:马达/运动/点火控制器和驱动器 H-BRIDGE MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。