- 您现在的位置：买卖IC网 > PDF目录39188 > LB1846M STEPPER MOTOR CONTROLLER, 0.8 A, PDSO10 PDF资料下载
参数资料
| 型号： | LB1846M |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 0.8 A, PDSO10 |
| 封装： | 6.50 X 5.10 MM, MFP-10 |
| 文件页数： | 4/8页 |
| 文件大小： | 117K |
| 代理商： | LB1846M |
Block Diagrams
[LB1846M]
[LB1848M]
Note: When the “soft off” function is used, a capacitor must be connected to the SOF pin. If this function is not used, this pin must be left open with absolutely
no signals or lines connected.
Notes on Wiring and Lines
Since large currents flow in the VCC and ground lines, oscillations may occur on these lines. The following points
should be observed if such oscillations occur.
(1) Lower the line impedances by making them shorter and thicker.
(2) Attach capacitors close to the IC.
(3) If the controller (CPU) is mounted on a separate printed circuit board, insert series resistors (of about 10 k
)
between the controller outputs and this IC.
No. 5339-4/8
LB1846M, 1848M
相关PDF资料 |
PDF描述 |
|---|---|
| LB1855NM | BRUSHLESS DC MOTOR CONTROLLER, 1.2 A, PDSO16 |
| LB1861M | BRUSHLESS DC MOTOR CONTROLLER, 1.5 A, PDSO14 |
| LB1860 | BRUSHLESS DC MOTOR CONTROLLER, PDIP10 |
| LB1861 | BRUSHLESS DC MOTOR CONTROLLER, PDIP10 |
| LB1862 | BRUSHLESS DC MOTOR CONTROLLER, 0.8 A, PDIP10 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LB1846M_99 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Low-Voltage/Low Saturation Voltage Type Bidirectional Motor Driver |
| LB1846MC | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Monolithic Digital IC Low-Voltage/Low Saturation Voltage Type Bidirectional Motor Driver |
| LB1846MC-AH | 功能描述:马达/运动/点火控制器和驱动器 GP DC MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB1846MC-R-AH | 制造商:ON Semiconductor 功能描述:H-BRIDGE MOTOR DRIVER - Tape and Reel |
| LB1846MC-ZH | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。