- 您现在的位置：买卖IC网 > PDF目录80092 > LB1862 BRUSHLESS DC MOTOR CONTROLLER, 0.8 A, PDIP10 PDF资料下载
参数资料
| 型号： | LB1862 |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 0.8 A, PDIP10 |
| 封装： | 0.300 INCH, DIP-10 |
| 文件页数： | 6/6页 |
| 文件大小： | 78K |
| 代理商： | LB1862 |
LB1862
PS No.6208-6/6
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellctual property rights which has resulted from the use of the technical information and products mentioned
above.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed
for volume production.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
Application Circuit Example
1
2
9
8
3
6
4
10
7
5
IN
IN+
HB
ST
CT
OUT2
OUT1
RD
VCC
GND
LB1862
H
C2
C1=0.47 to 1
F
(1) D1 is used to prevent IC destruction caused by reverse-connection. It can be omitted if no problems are expected.
(2) C2 would not be required for the internal fan PCB but required for the power supply line in order to reduce the power
line impedance and pass the regenerative current because a motor is basically an inductive load and it has a possibility
of large current when the power is first applied or in other cases.
(3) When CT is not used, it should be connected to ground.
(4) When RD, ST, and HB are not used, they should be left open or connected to ground.
This catalog provides information as of February, 2009. Specifications and information herein are subject
to change without notice.
相关PDF资料 |
PDF描述 |
|---|---|
| LT1460JCS3-3#TRPBF | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 3 V, PDSO3 |
| LT1460BIN8-5#TRPBF | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 5 V, PDIP8 |
| LS5540-9PD5T | 2-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
| LS5540-9PD8T | 2-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
| LSN-1.5/10-D12J | DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LB1862_09 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:For Fan Motor Single-Phase Full-Wave Driver |
| LB1862-E | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB1862M | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Fan Motor Single-Phase Full-Wave Drivers |
| LB1862M_09 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:For Fan Motor Single-Phase Full-Wave Driver |
| LB1862MC | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Monolithic Digital IC For Fan Motor Single-Phase Full-Wave Driver |
发布紧急采购，3分钟左右您将得到回复。