参数资料
型号: LB1930M
厂商: SANYO SEMICONDUCTOR CO LTD
元件分类: 运动控制电子
英文描述: BRUSH DC MOTOR CONTROLLER, 1 A, PDSO10
封装: 0.225 INCH, MFP-10
文件页数: 5/5页
文件大小: 78K
代理商: LB1930M
LB1930M
PS No.6068-5/5
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellctual property rights which has resulted from the use of the technical information and products mentioned
above.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed
for volume production.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
Usage Notes
Oscillation may occur in the VCC and P-GND lines, since these lines carry a wide range of currents. The following
may help if this is a problem.
(1) Lower the inductance of the wiring by making lines wider and shorter.
(2) Insert capacitors with good frequency characteristics close to the IC.
(3) Consider adopting the following methods if the CPU and this IC are mounted on different printed circuit boards that
could easily have different ground potentials.
Connect S-GND to the CPU ground and connect P-GND to the power system ground.
Insert resistors of about 10k in series between the controller outputs and the inputs on this IC.
This catalog provides information as of February, 2009. Specifications and information herein are subject
to change without notice.
相关PDF资料
PDF描述
LB1934T BRUSH DC MOTOR CONTROLLER, 2 A, PDSO20
LB1941T VOICE COIL MOTOR CONTROLLER, 0.6 A, PDSO8
LB1943 BRUSH DC MOTOR CONTROLLER, 1.6 A, PSIP10
LB1971V DISK DRIVE MOTOR CONTROLLER, 0.7 A, PDSO24
LB1976 BRUSHLESS DC MOTOR CONTROLLER, 2.5 A, PDIP28
相关代理商/技术参数
参数描述
LB1930M_11 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Low-Voltage, Low-Saturation Bidirectional Motor Driver
LB1930MC 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Monolithic Digital IC Low-Voltage, Low-Saturation Bidirectional Motor Driver
LB1930MC-AH 功能描述:马达/运动/点火控制器和驱动器 2.2-10.8V 1ch Brsuh Motor Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
LB1930MC-BH 功能描述:马达/运动/点火控制器和驱动器 GP DC MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
LB1930MCGEVB 功能描述:电源管理IC开发工具 EVM FOR LB1930MC RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V