参数资料
| 型号： | LC717A00AR-NH |
| 厂商： | ON Semiconductor |
| 文件页数： | 2/11页 |
| 文件大小： | 0K |
| 描述： | IC TOUCH SENSOR CAP-DGTL VCT28 |
| 标准包装： | 2,000 |
| 系列： | * |
LC717A00AR
No.A2048-10/11
Details of Pin Functions
●Cin0 to Cin7
These are the capacitance-sensor-input pins. These pins are used by connecting them to the touch switch pattern. Cin
and the Cdrv wire patterns should be close to each other. By doing so, Cdrv and Cin patterns are capacitively coupled.
Therefore, LSI can detect capacitance change near each pattern as 8bit digital data.
However, if the shape of each pattern or the capacitively coupled value of Cdrv is not appropriate, it may not be able
to detect the capacitance change correctly.
In this LSI, there is a two-stage amplifier that detects the changes in the capacitance and outputs analog-amplitude
values. Cin0 to Cin7 are connected to the inverting input of the 1st amplifier in the LSI.
During measurement process, channels other than the one being measured are all in “Low” condition.
Leave the unused terminals open.
●Cref
It is the reference-capacitance-input pin. It is used by connecting to the wire pattern like Cin pins or is used by
connecting any capacitance between this pin and Cdrv pin.
In this LSI, there is a two-stage amplifier that detects the changes in the capacitance and outputs analog-amplitude
values. Cref is connected to the non-inverting input of the 1st amplifier in the LSI.
Due to the parasitic capacitance generated in the wire connections of Cin pins and their patterns, as well as the one
generated between the wire patterns of Cin and Cdrv pins, Cref may not detect capacitance change of each Cin pin
accurately. In this case, connect an appropriate capacitance between Cref and Cdrv to detect capacitance change
accurately.
However, if the difference between the parasitic capacitance of each Cin pin is extremely large, it may not detect
capacitance change in each Cin pin correctly.
●Pout0 to Pout7
These are the detection-result-output pins. The capacitance detection results of Cin0 to Cin7 are compared with the
threshold of the LSI. The pin outputs a “High” or a “Low” depending on the result.
●ERROR
It is the error-occurrence-status-output pin.
It outputs “Low” during normal operation. If there is a calibration error or a system error, it outputs “High” to indicate
that an error occurred.
●Cdrv
It is the output pin for capacitance sensors drive. It outputs the pulse voltage which is needed to detect capacitance at
Cin0 to Cin7.
Cdrv and Cin wire patterns should be close to each other so that they are capacitively coupled.
●INTOUT
It is the interrupt-output pin. It outputs “High” when a measurement process is completed.
Connect to a main microcomputer if necessary, and use as interrupt signal.
Leave the terminal open if not in used.
●SCL/SCK
Clock input (I2C) / Clock input (SPI)
It is the clock input pin of the I2C compatible bus or the SPI depending on the mode of operation.
If interface is not to be used, fix the pin to “High”. However, even if interface is not to be used, providing a
communication terminal on board is still recommended.
●GAIN
In this LSI, there is a two-stage amplifier that detects the changes in the capacitance and outputs analog-amplitude
values. It is the selection pin of the initial value of gain of the 2nd amplifier.
Even if this LSI is used alone, gain setting can still be selected through this terminal. At initialization of the LSI, it is
set to 7-times higher than the minimum setting when GAIN pin is “Low”, and is set to 14-times higher than the
minimum setting when GAIN pin is “High”.
相关PDF资料 |
PDF描述 |
|---|---|
| LC75700T-MPB-E | IC KEY SCANNING LSI 20TSSOP |
| LC87F2932AU-CD-E | IC MCU 8BIT 32K FLASH 64TQLP |
| LFECP33E-4FN672I | IC FPGA 32.8KLUTS 672FPBGA |
| LFX200B-05FN256C | IC FPGA 200K GATES 256-BGA |
| LFXP20E-5F484C | IC FPGA 19.7KLUTS 340I/O 484-BGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LC717A00ARZ-NH | 制造商:ON Semiconductor 功能描述:TOUCH SENSOR IC - Tape and Reel 制造商:ON Semiconductor 功能描述:REEL / TOUCH SENSOR IC |
| LC717A10AJ | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Capacitance-Digital-Converter LSI for Electrostatic Capacitive Touch Sensors |
| LC717A10AJ-AH | 功能描述:电容触摸传感器 TOUCH SENSOR IC RoHS:否 制造商:Microchip Technology 电源电压: 通道数量: 封装 / 箱体: 尺寸: 温度范围: |
| LC717A10AR | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Capacitance-Digital-Converter LSI for Electrostatic Capacitive Touch Sensors |
| LC717A10ARGPGEVB | 制造商:ON Semiconductor 功能描述:SE - STANDARD LSI PRODUCTS 1 - Bulk |
发布紧急采购，3分钟左右您将得到回复。