- 您现在的位置：买卖IC网 > PDF目录30735 > LC75412E 2 CHANNEL(S), TONE CONTROL CIRCUIT, PQFP64 PDF资料下载
参数资料
| 型号： | LC75412E |
| 元件分类： | 音频控制 |
| 英文描述： | 2 CHANNEL(S), TONE CONTROL CIRCUIT, PQFP64 |
| 封装： | QIP-64 |
| 文件页数： | 11/21页 |
| 文件大小： | 204K |
| 代理商： | LC75412E |
Usage Cautions
(1) Data transmission at power ON
The status of internal analog switches is unstable at power ON. Therefore, perform muting or some other
countermeasure until the data has been set.
(2) Description of zero-cross switching circuit operation
The LC75412E and 75412W have a function to switch zero-cross comparator signal detection locations, enabling the
selection of the optimum detection location for blocks whose data is to be updated. Basically, the switching noise can
be minimized by inputting the signal immediately following the block whose data is to be updated to the zero-cross
comparator, so it is necessary to switch the detection location every time.
LC75412E, 75412W Zero-Cross Detection Circuit
No. 7053-19/21
LC75412E, 75412W
Volume
Tone
Switch
Fader
Zero-cross
comparator
Selector
(3) Zero-cross switching control method
The zero-cross switching control method consists of setting the zero-cross control bits to the zero-cross detection
mode (D36, D37 = 0), and specifying the detection blocks (D38, D39) before transmitting the data. These control bits
are latched immediately following data transfer, that is to say beforehand in sync with the falling edge of CE, so when
updating data of volumes, etc., it is possible to perform mode setting and zero-cross switching with one data transfer.
An example of control when updating the data of the volume block is shown below.
Zero-cross detection
mode setting
Volume block
setting
D36
D37
D38
D39
0
1
0
(4) Zero-cross timer setting
If the input signal becomes lower than the zero-cross comparator detection sensitivity, or if only low-frequency
signals are input, zero-cross detection continues to be impossible, and data is not latched during this time.
The zero-cross timer can set a time for forcible latch during such a status when zero-cross detection is not possible.
For example, to set 25 ms,
using T = 0.69CR and C = 0.033 F,
we obtain
Normally, a value between 10 ms and 50 ms is set.
R=
1.1 M
25
× 10–3
0.69
× 0.033 × 10 –6
相关PDF资料 |
PDF描述 |
|---|---|
| LC75412W | 2 CHANNEL(S), TONE CONTROL CIRCUIT, PQFP64 |
| LC75412WS | VOLUME CONTROL CIRCUIT, PQFP64 |
| LC75421M | 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO36 |
| LC7565B | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| LC7565 | SPECIALTY CONSUMER CIRCUIT, PDIP42 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LC75412EH-E | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| LC75412W | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Electronic Volume Controller for Car Audio Systems |
| LC75412WH-D-E | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| LC75412WH-E | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| LC75412WS | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Electronic Volume Controller for Car Audio Systems |
发布紧急采购，3分钟左右您将得到回复。