- 您现在的位置：买卖IC网 > PDF目录17738 > LD6806CX4/25P,315 (NXP Semiconductors)IC REG LDO 200MA 2.5V 4WLCSP PDF资料下载
参数资料
| 型号： | LD6806CX4/25P,315 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 6/36页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 200MA 2.5V 4WLCSP |
| 标准包装： | 9,000 |
| 系列： | * |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
NXP Semiconductors
LD6806 series
Ultra low-dropout regulator, low noise, 200 mA
7. Thermal characteristics
Table 9.
Thermal characteristics
Symbol
Parameter
Conditions
Typ
Unit
R th(j-a)
thermal resistance from junction to ambient
LD6806CX4/xxx,
[1][2]
130
K/W
LD6806CX4/Cxxx
LD6806F/xxx
LD6806TD/xxx
[1][2]
[1][2]
220
125
K/W
K/W
[1]
[2]
The overall R th(j-a) can vary depending on the board layout. To minimize the effective R th(j-a) , all pins must have a solid connection to
larger Cu layer areas for example to the power and ground layer. In multi-layer PCB applications, the second layer should be used to
create a large heat spreader area directly below the LDO. If this layer is either ground or power, it should be connected with several vias
to the top layer connecting to the device ground or supply. Avoid the use of solder-stop varnish under the chip.
Use the measurement data given for a rough estimation of the R th(j-a) in your application. The actual R th(j-a) value can vary in applications
using different layer stacks and layouts.
8. Characteristics
Table 10. Electrical characteristics
At recommended input voltages and T amb = ? 40 ? C to +85 ? C; voltages are referenced to GND (ground = 0 V);
unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
? V O
output voltage variation
V OUT < 1.8 V; I OUT = 1 mA
T amb = +25 ? C
? 30 ? C ? T amb ? +85 ? C
? 3
? 4
? 0.5
-
+3
+4
%
%
V OUT ? 1.8 V; I OUT = 1 mA
T amb = +25 ? C
? 30 ? C ? T amb ? +85 ? C
? 2
? 3
? 0.5
-
+2
+3
%
%
Line regulation error
? V O /(V O x ? V I )
relative output voltage
V IN = (V O(nom) + 0.2 V) to 5.5 V
? 0.1 -
+0.1
%/V
variation with input voltage
Load regulation error
? V O /(V O x ? I O )
relative output voltage
1 mA ? I OUT ? 200 mA
variation with output current
LD6806CX4/xxx, LD6806CX4/Cxxx
-
0.0025 0.01
%/mA
V do
dropout voltage
LD6806F/xxx, LD6806TD/xxx
I OUT = 200 mA; V IN > V O(nom)
LD6806CX4/xxx, LD6806CX4/Cxxx
LD6806F/xxx, LD6806TD/xxx
-
-
-
0.005
60
80
0.02
100
130
%/mA
mV
mV
V IL
V IH
I OUT
LOW-level input voltage
HIGH-level input voltage
current on pin OUT
pin EN
pin EN
0
1.4
-
-
-
-
0.4
5.5
200
V
V
mA
I OM
peak output current
V IN = (V O(nom) + 0.2 V) to 5.5 V
V O(nom) > 1.8 V;
300
-
-
mA
V OUT ? 0.95 ? V O(nom)
V O(nom) < 1.8 V;
300
-
-
mA
V OUT ? 0.9 ? V O(nom)
LD6806_SER
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 9 December 2011
? NXP B.V. 2011. All rights reserved.
6 of 36
相关PDF资料 |
PDF描述 |
|---|---|
| MG1608-202Y | BEAD FERRITE 2000 OHM 50MA 1608 |
| 3362S-1-253 | TRIMMER 25K OHM 0.5W TH |
| MZ1608-152Y | BEAD FERRITE 1500 OHM 50MA 1608 |
| W2A4YA220KAT2A | CAP ARRAY 4CH 22PF 16V 0508 |
| 6PA104 | SWITCH LEVER ARM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LD6806F | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Ultra low-dropout regulator, low noise, 200 mA |
| LD6806F/12H | 制造商:NXP Semiconductors 功能描述:LDO 1.2V SOT886 制造商:NXP Semiconductors 功能描述:LDO, 1.2V, SOT886 |
| LD6806F/12H,115 | 功能描述:低压差稳压器 - LDO LD6806 ULTRA LOW-DO VOLT REG 200MA RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| LD6806F/12P | 制造商:NXP Semiconductors 功能描述:LDO 1.2V 200MA 6SOT886 |
| LD6806F/12P,115 | 功能描述:低压差稳压器 - LDO 2.3-5.5VIN 1.2VOUT RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。