- 您现在的位置：买卖IC网 > Datasheet目录336 > LDS8160-002-T2 (IXYS)IC LED DVR WHT/RGB BCKLGT 16WQFN Datasheet资料下载
参数资料
| 型号： | LDS8160-002-T2 |
| 厂商： | IXYS |
| 文件页数： | 26/39页 |
| 文件大小： | 0K |
| 描述： | IC LED DVR WHT/RGB BCKLGT 16WQFN |
| 标准包装： | 1 |
| 系列： | LED-Sense™, PowerLite™ |
| 拓扑： | 线性（LDO），PWM |
| 输出数： | 6 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | RGB，白色 LED |
| 频率： | 1.2MHz |
| 电源电压： | 2.3 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 供应商设备封装： | 16-TQFN |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 85°C |
| 其它名称： | LDS8160-002-T2-6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
LDS8160
V F = 3.2V + [-1.5 mV/ C x (50 C - 25 C)] = 3.163V for
V F = 3.2V + [-1.3 mV/ C x (50 C - 25 C)] = 3.168V for
mA is the de-rating current for each 5 C.
de-rate to ~ 45mW at 85 C and diodes must be turned
At 85 C, the R, G , B forward voltages will be reduced
maintaining the 50 C current ratios, the B -LED current
The total power dissipated by RGB LEDs at 85 C is
I R must de-rate from 18 mA to ~ 6.19 mA from 50 C to
Table 8 of LDS8160 datasheet) from 55 C to 85 C.
LED
0 0 0
Green LED, and
0 0 0
Blue LED.
The total RGB LED power at a 50 0 C with the applied
inverse curves to equalize the luminosity vs.
temperature would be
( 2.05V x 18mA) + ( 3.16 V x 15.6 mA) + ( 3.17 V x
15mA) =~ 133.mW
The total RGB LED power for NSSM038AT-E must be
less than ~ 133 mW up to the de-rating point at 50 0 C
(see Figure 2) complies with our result.
Also from the curve in Figure 2, the total power must
0
off at higher temperatures.
0
to ~ 1.98 V , 3.11 V , and 3.12 V respectively.
The de-rating is achieved by decreasing LED currents
in constant steps (i.e. linear rate) from 50 0 C to 85 0 C to
meet the final 45 mW power dissipation.
To maintain the luminosity equalization during the de-
rating, the 50 0 C current ratios between Red, Green,
and Blue LED currents (i.e. 1.2:1.04:1) should be
preserved.
With nominal forward current, I = 15mA, and
0
at the end of de-rating (before shutdown) is calculated
as follows;
0
P 85C = (1.2 x I x V R_85C ) + (1.04 x I x V G_85C ) + (1 x I x
V B_85C ) = (1.2 x I x 1.98V ) + (1.04 x I x 3.11 V ) + (1 x I
x 3.12 V ) = 45 mW ,
where I is the Blue LED current at 85 0 C.
Solving for I gives us I = ~ 45 mW / 8.73 V = 5.16mA
for Blue, 5.37 mA for Green, and 6.19 mA for Red
LED.
0
85 0 C (seven 5 0 C steps).
For linear de-rate, each step is 18mA - 6.19mA / 7 = ~
1.69mA/step. Using the 2- x ΔPW M code scale, this is
met with the codes shown in the R -LUT table (See
0 0
In LOG mode the Δ PWM table entries for the de-rating
are found by first taking the current of the prior step
minus the de-rating current per step, then dividing the
result by the prior step current, and finally converting
to a number of dB step.
The following example clarifies:
Using prior data for RED LED, we will find required
de-rating Δ R in dB at 55oC
Δ R @ 55oC = 20Log [(18 mA – 1.69 mA) / 18 ma] =
-0.856 dB,
where 18 mA is the current for the 50oC point and 1.69
0
Dividing this value by 0.34 dB/step (in 2-x scale used for
de-rating) and rounding result to the nearest integer value
give us follow Δ PWM code
Δ PWM = INT (-0.846 dB / 0.34 dB/step) = -3 = 1101 (bin)
(see Table 8 of LDS8160 datasheet).
The Δ PWM value would then be
Δ PWM @ 60oC = INT {20Log [(16.31mA – 1.69 mA) /
16.31 mA] / 0.34} = -3 =. 1101 (bin)
Δ PWM @ 65oC = INT {20Log [(14.62 mA – 1.69 ma) /
14.62 mA) = -3 =. 1101 (bin)
Δ PWM @ 70oC = INT {20Log [(12.93 mA – 1.69 ma) /
12.93 mA) = -4 =. 1100 (bin)
Δ PWM @ 75oC = INT {20Log [(11.24 mA – 1.69 ma) /
11.24 mA) = -4 =. 1100 (bin)
Δ PWM @ 80oC = INT {20Log [(9.55 mA – 1.69 ma) / 9.55
mA) = -5 =. 1011 (bin)
Δ PWM @ 85oC = INT {20Log [(7.86 mA – 1.69 ma) / 8.1
mA) = -6 =. 1010 (bin)
At temperatures higher than 85oC, the LED current should
be zero mA due to the shutdown temperature defined as
above 85 0 C. Therefore, LUT Δ PWM entries for shutdown
regions are not used and may be zero.
To set LED current in shutdown at temperature above
85 0 C, write 85 0 C T-code (11000 (bin)) with leading 1, i.e.
111000 (bin) = 38h, into register 4Ah (see Table 7 of
LDS8160 datasheet).
To maintain constant ratio between channels during the
de-rating, the Green and Blue channels can de- rated by
the same dB steps in Logarithmic mode as the Red
channel. This will maintain the same luminosity balance
as at the starting point of the de-rating.
Users can adjust luminosity balance in the de-rating
section too to further optimize balance. This requires
more customized table entries (i.e. ratios continue to
match Luminosity vs. Temperature curve even for
temperatures where de-rating is being applied). The
decided approach is user/application dependent.
Table A1.1 shows the completed table used as LDS8160
default for Nichia NSSM038AT-E RGB LED with the
assumptions overviewed in this example.
To aide users in building and loading their specific
correction tables IXYS can provide a software
development tool to map LED vendor information and
user defined operating points to final calculated LUT data
values. Please consult factory to obtain a copy.
? 2009 IXYS Corp.
Characteristics subject to change without notice
26
Doc. No. 8160_DS, Rev. N1.0
相关PDF资料 |
PDF描述 |
|---|---|
| LDS8620-002-T2 | IC LED DRIVER FLASH 16WQFN |
| LDS8621002-T2-960 | IC LED DRIVER FLASH 16WQFN |
| LDS8680008-T2 | IC LED DRIVER PHOTO FLASH 16WQFN |
| LDS8681008-T2 | IC LED DRIVER PHOTO FLASH 16WQFN |
| LDS8711 | IC LED DRIVER PWM 32MA 8TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LDS8161-002-T2 | 功能描述:LED照明驱动器 6-Chan High-Side WLED Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| LDS85-750 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| LDS8620-002-T2 | 功能描述:LED照明驱动器 200mA Dual Output Flash/Lamp Drvr RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| LDS8621-002-T2 | 功能描述:LED照明驱动器 200mA Dual Output Flash/Lamp Drvr RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| LDS8621002-T2-960 | 功能描述:IC LED DRIVER FLASH 16WQFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:PowerLite™ 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C |
发布紧急采购，3分钟左右您将得到回复。