参数资料
型号: LFEC1E-4TN100C
厂商: Lattice Semiconductor Corporation
文件页数: 86/163页
文件大小: 0K
描述: IC FPGA 1.5KLUTS 67I/O 100-TQFP
标准包装: 90
系列: EC
逻辑元件/单元数: 1500
RAM 位总计: 18432
输入/输出数: 67
电源电压: 1.14 V ~ 1.26 V
安装类型: 表面贴装
工作温度: 0°C ~ 85°C
封装/外壳: 100-LQFP
供应商设备封装: 100-TQFP(14x14)
其它名称: 220-1771
LFEC1E-4TN100C-ND
2-26
Architecture
LatticeECP/EC Family Data Sheet
Figure 2-31. Tristate Register Block
Control Logic Block
The control logic block allows the selection and modification of control signals for use in the PIO block. A clock is
selected from one of the clock signals provided from the general purpose routing and a DQS signal provided from
the programmable DQS pin. The clock can optionally be inverted.
The clock enable and local reset signals are selected from the routing and optionally inverted. The global tristate
signal is passed through this block.
DDR Memory Support
Implementing high performance DDR memory interfaces requires dedicated DDR register structures in the input
(for read operations) and in the output (for write operations). As indicated in the PIO Logic section, the LatticeEC
devices provide this capability. In addition to these registers, the LatticeEC devices contain two elements to simplify
the design of input structures for read operations: the DQS delay block and polarity control logic.
DLL Calibrated DQS Delay Block
Source Synchronous interfaces generally require the input clock to be adjusted in order to correctly capture data at
the input register. For most interfaces a PLL is used for this adjustment. However in DDR memories the clock
(referred to as DQS) is not free running so this approach cannot be used. The DQS Delay block provides the
required clock alignment for DDR memory interfaces.
The DQS signal (selected PIOs only) feeds from the PAD through a DQS delay element to a dedicated DQS routing
resource. The DQS signal also feeds polarity control logic, which controls the polarity of the clock to the sync regis-
ters in the input register blocks. Figures 2-32 and 2-33 show how the DQS transition signals are routed to the PIOs.
The temperature, voltage and process variations of the DQS delay block are compensated by a set of calibration
(6-bit bus) signals from two DLLs on opposite sides of the device. Each DLL compensates DQS Delays in its half of
the device as shown in Figure 2-33. The DLL loop is compensated for temperature, voltage and process variations
by the system clock and feedback loop.
D
LE*
Q
D
Q
D-Type
ONEG1
CLK1
Programmed
Control
TO
Latch
*Latch is transparent when input is low.
OPOS1
OUTDDN
/LATCH
0
1
0
1
From
Routing
To sysIO
Buffer
TD
相关PDF资料
PDF描述
RNM-053.3S CONV DC/DC 1W SGL 3.3V OUT DIP6
PT5406C REG 1.2V 6A 5/3.3VIN SMD
RNM-1205S CONV DC/DC 1W SGL 5V OUT DIP6
RCB66DHAS-S621 EDGECARD 132POS DIP R/A .050 SLD
5174216-5 CONN D-CAP MALE PINS 20POS VERT
相关代理商/技术参数
参数描述
LFEC1E-4TN100I 功能描述:FPGA - 现场可编程门阵列 1.5K LUTs 67 IO 1.2V -4 Spd I RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 栅极数量: 逻辑块数量:943 内嵌式块RAM - EBR:1956 kbit 输入/输出端数量:128 最大工作频率:800 MHz 工作电源电压:1.1 V 最大工作温度:+ 70 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-256
LFEC1E-4TN144C 功能描述:FPGA - 现场可编程门阵列 1.5K LUTs Pb-Free RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 栅极数量: 逻辑块数量:943 内嵌式块RAM - EBR:1956 kbit 输入/输出端数量:128 最大工作频率:800 MHz 工作电源电压:1.1 V 最大工作温度:+ 70 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-256
LFEC1E-4TN144I 功能描述:FPGA - 现场可编程门阵列 1.5K LUTs 97 IO 1.2V -4 Spd I RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 栅极数量: 逻辑块数量:943 内嵌式块RAM - EBR:1956 kbit 输入/输出端数量:128 最大工作频率:800 MHz 工作电源电压:1.1 V 最大工作温度:+ 70 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-256
LFEC1E-5F256C 制造商:LATTICE 制造商全称:Lattice Semiconductor 功能描述:LatticeECP/EC Family Data Sheet
LFEC1E-5F256I 制造商:LATTICE 制造商全称:Lattice Semiconductor 功能描述:LatticeECP/EC Family Data Sheet