- 您现在的位置：买卖IC网 > PDF目录6704 > LIA120STR (IXYS Integrated Circuits Division)OPTOISOLATOR ERROR AMP 8-SMD PDF资料下载
参数资料
| 型号： | LIA120STR |
| 厂商： | IXYS Integrated Circuits Division |
| 文件页数： | 7/10页 |
| 文件大小： | 0K |
| 描述： | OPTOISOLATOR ERROR AMP 8-SMD |
| 标准包装： | 1,000 |
| 通道数： | 1 |
| 输入类型： | DC |
| 电压 - 隔离： | 3750Vrms |
| 电流传输比（最小值）： | 1% @ 5mA |
| 电流传输比（最大）： | 3% @ 5mA |
| 输出类型： | 光电型 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SMD，鸥翼型 |
| 包装： | 带卷 (TR) |
I NTEGRATED C IRCUITS D IVISION
The LIA120
The LIA120 is an optically-coupled isolated linear error
amplifier. It integrates three of the most fundamental
elements necessary to make an isolated power supply:
LIA120
K 3 is taken from the datasheet as 1 nominally. The AC
gain of the setup can be represented by:
a reference voltage, an error amplifier, and an isolated
coupling device. It is functionally equivalent to a 431
type shunt regulator plus a linear optical amplifier.
A V V OUT /V IN
=
R L
R 1
R 2 R 1
1
G m CTR FB
1
Powering the Isolated Input
The isolated input of the LIA120 is powered through
the LED pin (pin 8) via the part to its isolated
ground at pin 5. The typical operating current of
the device is determined by the output voltage and
current requirements as well as the CTR of the
linear optocoupler. For Figure 7, the LED current
requirement is set by the following equation.
G m CTR Forward
Where:
? G m = 1/Z OUT which is ~ 3 Siemens
? CTR FB is approximately CTR Forward = 0.02 nominally
CTR FB = K 1 , CTR FORWARD = K 2 , CTR FORWARD /CTR FB = K 3
This calculation provides a more accurate gain
calculation, but is only necessary when the voltage
I LED =
V out,bias
R L K 1
divider resistor’s impedance is becoming close to the
optical output impedance of the shunt regulator.
The output voltage is typically constrained by the user
to satisfy the design requirements of the application
circuit. Design considerations must also take into
account that R L affects the total gain and that CTR
gains vary with process. Nominally the LED current
should be around 1-2mA but can be as high as
10-15mA if the user requires.
LED current is limited by the resistor in series with pin
8, the LED pin, to the supply and is typically 10-100
ohms for operating currents of 1-2mA. The minimum
operating voltage of 2.74V for the LIA120 from pin 8
to pin 5 is based on the sum of the voltage drop of the
LED and the operational voltage headroom of the 431.
Minimum operating voltage for the application circuit
is therefore the sum of the LIA120 minimum operating
voltage plus the voltage drop of the current limiting
resistor For a design with 1mA of LED current and
a current limiting resistor of 100 ohms, the minimum
operating voltage is calculated to be 2.74 + (0.001)
(100) = 2.84V.
Feedback
Setting the gain for the LIA120 is accomplished simply
by setting two resistors. The application circuit in
Figure 6 shows a resistor divider feeding the FB pin,
so the operating conditions for the gain are governed
by:
Compensation
The LIA120 is relatively easy to compensate but two
factors must be considered when analyzing the circuit.
The frequency response of the LIA120 can be as
high as 40kHz, but must be limited because of the
closed loop optical feedback to the input signal. In
the localized optical feedback there are two poles to
consider, the 431 dominant pole and the linear optical
coupler pole. The open loop gain of the optical loop
(for the application diagram) is:
A v, OPTICAL = Gm CTR FB R 1 R 2
The open loop gain is affected by the selection of R 1
and R 2 , and without any compensation the circuit may
oscillate. The addition of a compensation network (C c
and R c ) control the maximum bandwidth so that open
loop gain is rolling off long before the optical pole
causes the circuit to oscillate. The optical pole is at
~180kHz so the bandwidth is typically limited to less
than 40kHz.
While there is flexibility in the part to change the
compensation technique, the upper limit on frequency
response is generally desired to be such that the
circuit will not oscillate for a large selection of R 1 and
R 2 . Therefore the compensation capacitor should not
be less than 100pF, which gives adequate bandwidth
R 1 Vin Vout R 1
R04
= -
R 2 Vref Vref R L
1
K 3
-1
for most designs.
www.ixysic.com
7
相关PDF资料 |
PDF描述 |
|---|---|
| 1591UBU | BOX ABS 4.72X4.72X2.32" BLUE |
| LDA203STR | OPTOCOUPLER SGL TRANS-OUT 8-SMD |
| H65,TRGR | BOX 4.94X2.75X.94 STD TRANS GRN |
| 2-1393844-9 | RELAY GEN PURPOSE DPDT 25A 24V |
| 152W,AL | BOX 5.62X3.25X2.00 WALL MT AMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LIA130 | 功能描述:光隔离放大器 Linear Optocoupler RoHS:否 制造商:Avago Technologies 绝缘电压:5000 Vrms 参考电压: 电流传递比: 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| LIA130S | 功能描述:固态继电器-PCB安装 Linear Optocoupler RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT |
| LIA130STR | 功能描述:固态继电器-PCB安装 Linear Optocoupler RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT |
| LIA135 | 功能描述:Isolation Amplifier 1 Circuit 8-DIP 制造商:ixys integrated circuits division 系列:- 包装:管件 零件状态:有效 放大器类型:隔离 电路数:1 输出类型:- 压摆率:- 增益带宽积:10kHz -3db 带宽:- 电流 - 输入偏置:340nA 电压 - 输入失调:- 电流 - 电源:- 电流 - 输出/通道:- 电压 - 电源，单/双（±）:- 工作温度:-40°C ~ 85°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商器件封装:8-DIP 标准包装:50 |
| LIA135S | 功能描述:Isolation Amplifier 1 Circuit 8-SMD 制造商:ixys integrated circuits division 系列:- 包装:管件 零件状态:有效 放大器类型:隔离 电路数:1 输出类型:- 压摆率:- 增益带宽积:10kHz -3db 带宽:- 电流 - 输入偏置:340nA 电压 - 输入失调:- 电流 - 电源:- 电流 - 输出/通道:- 电压 - 电源，单/双（±）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SMD，鸥翼型 供应商器件封装:8-SMD 标准包装:50 |
发布紧急采购，3分钟左右您将得到回复。