- 您现在的位置：买卖IC网 > PDF目录43919 > LIS2L02ALTR (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PBGA8 PDF资料下载
参数资料
| 型号： | LIS2L02ALTR |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PBGA8 |
| 封装： | 5 X 5 MM, 1.60 MM HEIGHT, GREEN, PLASTIC, LGA-8 |
| 文件页数： | 16/17页 |
| 文件大小： | 219K |
| 代理商： | LIS2L02ALTR |
Obsolete
Product(s)
- Obsolete
Product(s)
Mechanical and electrical specifications
LIS2L02AL
8/17
Self Test allows to test the mechanical and electric part of the sensor, allowing the seismic
mass to be moved by means of an electrostatic test-force. The Self Test function is off when
the ST pin is connected to GND. When the ST pin is tied at Vdd an actuation force is applied
to the sensor, simulating a definite input acceleration. In this case the sensor outputs will
exhibit a voltage change in their DC levels which is related to the selected full scale and
depending on the Supply Voltage through the device sensitivity. When ST is activated, the
device output level is given by the algebraic sum of the signals produced by the acceleration
acting on the sensor and by the electrostatic test-force. If the output signals change within
the amplitude specified inside Table 2, than the sensor is working properly and the
parameters of the interface chip are within the defined specification.
Output impedance describes the resistor inside the output stage of each channel. This
resistor is part of a filter consisting of an external capacitor of at least 1nF and the internal
resistor. Due to the high resistor level only small, inexpensive external capacitors are
needed to generate low corner frequencies. When interfacing with an ADC it is important to
use high input impedance input circuitries to avoid measurement errors. Note that the
minimum load capacitance forms a corner frequency beyond the resonance frequency of
the sensor. For a flat frequency response a corner frequency well below the resonance
frequency is recommended. In general the smallest possible bandwidth for an particular
application should be chosen to get the best results.
相关PDF资料 |
PDF描述 |
|---|---|
| LIS302ALKTR | MOTION SENSOR, PBGA14 |
| LIS302DLHTR | SPECIALTY ANALOG CIRCUIT, PBGA14 |
| LIS302DL | SPECIALTY ANALOG CIRCUIT, PQCC14 |
| LIS302DLTR8 | SPECIALTY ANALOG CIRCUIT, PQCC14 |
| LIS331ALTR | SPECIALTY ANALOG CIRCUIT, QCC16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LIS2L02AO | 制造商:STMicroelectronics 功能描述:TWO-AXIS MEMS-BASED ACCELEROMETER - Bulk |
| LIS2L02AQ | 功能描述:ACCELEROMETER DUAL AXIS 44QFN RoHS:是 类别:传感器，转换器 >> 加速计 系列:- 标准包装:1 系列:SCA1000 轴:X，Y 加速范围:±1.7g 灵敏度:1.2V/g 电源电压:4.75 V ~ 5.25 V 输出类型:数字 带宽:50±30Hz 接口:SPI 安装类型:表面贴装 封装/外壳:12-SMD 供应商设备封装:12-SMD 其它名称:551-1007-1 |
| LIS2L02AQ_04 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:INERTIAL SENSOR-2Axis - 2g/6g LINEAR ACCELEROMETER |
| LIS2L02AQ3 | 功能描述:加速计 - 板上安装 2-axis +/-2g/+/-6g MEMS Intertial Sensr RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS2L02AQ3TR | 功能描述:加速计 - 板上安装 MEMS INERTIAL snsr 2 axis RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
发布紧急采购，3分钟左右您将得到回复。