- 您现在的位置：买卖IC网 > PDF目录43919 > LIS302DL (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PQCC14 PDF资料下载
参数资料
| 型号： | LIS302DL |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQCC14 |
| 封装： | 3 X 5 MM, 0.92 MM HEIGHT, 0.80 MM PITCH, GREEN, PLASTIC, TLGA-14 |
| 文件页数： | 20/42页 |
| 文件大小： | 602K |
| 代理商： | LIS302DL |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
LIS302DL
Register description
27/42
Zen bit enables the generation of Data Ready signal for Z-axis measurement channel when
set to 1. The default value is 1.
Yen bit enables the generation of Data Ready signal for Y-axis measurement channel when
set to 1. The default value is 1.
Xen bit enables the generation of Data Ready signal for X-axis measurement channel when
set to 1. The default value is 1.
7.3
CTRL_REG2 (21h)
SIM bit selects the SPI Serial Interface Mode. When SIM is ‘0’ (default value) the 4-wire
interface mode is selected. The data coming from the device are sent to SDO pad. In 3-wire
interface mode output data are sent to SDA_SDI pad.
BOOT bit is used to refresh the content of internal registers stored in the flash memory
block. At the device power up the content of the flash memory block is transferred to the
internal registers related to trimming functions to permit a good behavior of the device itself.
If for any reason the content of trimming registers was changed it is sufficient to use this bit
to restore correct values. When BOOT bit is set to ‘1’ the content of internal flash is copied
inside corresponding internal registers and it is used to calibrate the device. These values
are factory trimmed and they are different for every accelerometer. They permit a good
behavior of the device and normally they have not to be changed. At the end of the boot
process the BOOT bit is set again to ‘0’.
FDS bit enables (FDS=1) or bypass (FDS=0) the high pass filter in the signal chain of the
sensor
HP_coeff[2:1]. These bits are used to configure high-pass filter cut-off frequency ft.
Table 20.
CTRL_REG2 (21h) register
SIM
BOOT
--
FDS
HP_FF_W
U2
HP_FF_W
U1
HP_coeff2
HP_coeff1
Table 21.
CTRL_REG2 (21h) register description
SIM
SPI Serial Interface Mode selection. Default value: 0
(0: 4-wire interface; 1: 3-wire interface)
BOOT
Reboot memory content. Default value: 0
(0: normal mode; 1: reboot memory content)
FDS
Filtered Data Selection. Default value: 0
(0: internal filter bypassed; 1: data from internal filter sent to output register)
HP FF_WU2
High Pass filter enabled for FreeFall/WakeUp # 2. Default value: 0
(0: filter bypassed; 1: filter enabled)
HPFF_WU1
High Pass filter enabled for Free-Fall/Wake-Up #1. Default value: 0
(0: filter bypassed; 1: filter enabled)
HP coeff2
HP coeff1
High pass filter cut-off frequency configuration. Default value: 00
(See table below)
相关PDF资料 |
PDF描述 |
|---|---|
| LIS302DLTR8 | SPECIALTY ANALOG CIRCUIT, PQCC14 |
| LIS331ALTR | SPECIALTY ANALOG CIRCUIT, QCC16 |
| LIS331DLF | SPECIALTY ANALOG CIRCUIT, PBCC16 |
| LIS331DLHTR | SPECIALTY ANALOG CIRCUIT, PBCC16 |
| LIS331DLMTR | SPECIALTY ANALOG CIRCUIT, PBCC16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LIS302DL_07 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:MEMS motion sensor 3-axis - 【2g/【8g smart digital output “piccolo” accelerometer |
| LIS302DL_08 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:MEMS motion sensor 3-axis - ?± 2g/?± 8g smart digital output a??piccoloa?? accelerometer |
| LIS302DLH | 功能描述:加速计 - 板上安装 3 AXIS DIGITAL MEMS ACCELEROMETER RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS302DLHTR | 功能描述:加速计 - 板上安装 MEMS digital output L-Power Motion Snsr RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS302DLTR | 功能描述:加速计 - 板上安装 MEMS Motion Sensor RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
发布紧急采购，3分钟左右您将得到回复。