- 您现在的位置：买卖IC网 > PDF目录43919 > LIS331DL (STMICROELECTRONICS) MOTION SENSOR, PQCC16 PDF资料下载
参数资料
| 型号： | LIS331DL |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 模拟信号调理 |
| 英文描述： | MOTION SENSOR, PQCC16 |
| 封装： | 3 X 3 MM, 1 MM HEIGHT, GREEN, PLASTIC, LGA-16 |
| 文件页数： | 7/42页 |
| 文件大小： | 643K |
| 代理商： | LIS331DL |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
LIS331DL
Mechanical and electrical specifications
15/42
2.5
Terminology
2.5.1
Sensitivity
Sensitivity describes the gain of the sensor and can be determined e.g. by applying 1 g
acceleration to it. As the sensor can measure DC accelerations this can be done easily by
pointing the axis of interest towards the center of the Earth, noting the output value, rotating
the sensor by 180 degrees (pointing to the sky) and noting the output value again. By doing
so,
±1 g acceleration is applied to the sensor. Subtracting the larger output value from the
smaller one, and dividing the result by 2, leads to the actual sensitivity of the sensor. This
value changes very little over temperature and also over time. The Sensitivity Tolerance
describes the range of sensitivities of a large population of sensors.
2.5.2
Zero-g level
Zero-g level Offset (TyOff) describes the deviation of an actual output signal from the ideal
output signal if no acceleration is present. A sensor in a steady state on a horizontal surface
will measure 0 g in X axis and 0 g in Y axis whereas the Z axis will measure 1 g. The output
is ideally in the middle of the dynamic range of the sensor (content of OUT registers 00h,
data expressed as 2’s complement number). A deviation from ideal value in this case is
called Zero-g offset. Offset is to some extent a result of stress to MEMS sensor and
therefore the offset can slightly change after mounting the sensor onto a printed circuit
board or exposing it to extensive mechanical stress. Offset changes little over temperature,
see “Zero-g level change vs. temperature”. The Zero-g level tolerance (TyOff) describes the
Standard Deviation of the range of Zero-g levels of a population of sensors.
2.5.3
Self test
Self Test allows to check the sensor functionality without moving it. The self test function is
off when the self-test bit of CTRL_REG1 (control register 1) is programmed to ‘0‘. When the
self-test bit of ctrl_reg1 is programmed to ‘1‘ an actuation force is applied to the sensor,
simulating a definite input acceleration. In this case the sensor outputs will exhibit a change
in their DC levels which are related to the selected full scale through the device sensitivity.
When Self Test is activated, the device output level is given by the algebraic sum of the
signals produced by the acceleration acting on the sensor and by the electrostatic test-force.
If the output signals change within the amplitude specified inside Table 3, then the sensor is
working properly and the parameters of the interface chip are within the defined
specifications.
2.5.4
Click and double click recognition
The click and double click recognition functions help to create man-machine interface with
little software overload. The device can be configured to output an interrupt signal on
dedicated pin when tapped in any direction.
If the sensor is exposed to a single input stimulus it generates an interrupt request on inertial
interrupt pins (INT1 and/or INT2). A more advanced feature allows to generate an interrupt
request when a “double click” stimulus is applied. A programmable time between the two
events allows a flexible adaption to the application requirements. Mouse-button like
application, like clicks and double clicks, can be implemented.
This function can be fully programmed by the user in terms of expected amplitude and
timing of the stimuli.
相关PDF资料 |
PDF描述 |
|---|---|
| LIS331DLTR | MOTION SENSOR, PQCC16 |
| LIS331HH | SPECIALTY ANALOG CIRCUIT, PBCC16 |
| LIS332ARTR | SPECIALTY ANALOG CIRCUIT, PBGA16 |
| LIS332AX | SPECIALTY ANALOG CIRCUIT, PBGA16 |
| LIS33DE | SPECIALTY ANALOG CIRCUIT, PBGA16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LIS331DL | 制造商:STMicroelectronics 功能描述:ACCELEROMETER, MEMS, 3-AXIS, DIGITAL O/P, LGA-16; MEMS Sensor Output:Digital; Measurement Axis:X, Y, Z; Acceleration Range: 2g, 8g; Supply Voltage Min:2.16V; Supply Voltage Max:3.6V; Sensor Case Style:LGA; No. of Pins:16 ;RoHS Compliant: No |
| LIS331DL_08 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:MEMS motion sensor 3-axis - 【2g/【8g smart digital output -nano-accelerometer |
| LIS331DLF | 功能描述:加速计 - 板上安装 DGTL OUTPT MTN SEN MEMS ULTRA LO PWR RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS331DLFTR | 功能描述:加速计 - 板上安装 DGTL OUTPT MTN SEN MEMS ULTRA LO PWR RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS331DLH | 功能描述:加速计 - 板上安装 DGTL OUTPT MTN SEN MEMS ULTRA LO PWR RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
发布紧急采购，3分钟左右您将得到回复。