- 您现在的位置：买卖IC网 > PDF目录98000 > LIS35DE (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PBGA14 PDF资料下载
参数资料
| 型号： | LIS35DE |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PBGA14 |
| 封装： | 3 X 5 MM, 0.92 MM HEIGHT, 0.80 MM PITCH, GREEN, PLASTIC, LGA-14 |
| 文件页数： | 13/39页 |
| 文件大小： | 650K |
| 代理商： | LIS35DE |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
Digital interfaces
LIS35DE
20/39
Doc ID 15594 Rev 1
Figure 6.
Read and write protocol
CS is the Serial Port Enable and it is controlled by the SPI master. It goes low at the start of
the transmission and goes back high at the end. SPC is the Serial Port Clock and it is
controlled by the SPI master. It is stopped high when CS is high (no transmission). SDI and
SDO are respectively the Serial Port Data Input and Output. Those lines are driven at the
falling edge of SPC and should be captured at the rising edge of SPC.
Both the Read Register and Write Register commands are completed in 16 clock pulses or
in multiple of 8 in case of multiple byte read/write. Bit duration is the time between two falling
edges of SPC. The first bit (bit 0) starts at the first falling edge of SPC after the falling edge
of CS while the last bit (bit 15, bit 23, ...) starts at the last falling edge of SPC just before the
rising edge of CS.
bit 0: RW bit. When 0, the data DI(7:0) is written into the device. When 1, the data DO(7:0)
from the device is read. In latter case, the chip will drives SDO at the start of bit 8.
bit 1: MS bit. When 0, the address will remains unchanged in multiple read/write
commands. When 1, the address is auto incremented in multiple read/write commands.
bit 2-7: address AD(5:0). This is the address field of the indexed register.
bit 8-15: data DI(7:0) (write mode). This is the data that is written into the device (MSb first).
bit 8-15: data DO(7:0) (read mode). This is the data that will be read from the device (MSb
first).
In multiple read/write commands further blocks of 8 clock periods will be added. When MS
bit is 0 the address used to read/write data remains the same for every block. When MS bit
is 1 the address used to read/write data is incremented at every block.
The function and the behavior of SDI and SDO remain unchanged.
CS
SPC
SDI
SDO
RW
AD5 AD4 AD3 AD2 AD1 AD0
DI7DI6 DI5DI4 DI3DI2 DI1DI0
DO7DO6 DO5DO4 DO3DO2 DO1DO0
MS
相关PDF资料 |
PDF描述 |
|---|---|
| LIS35DETR | SPECIALTY ANALOG CIRCUIT, PBGA14 |
| LIS3L02AQ3TR | SPECIALTY ANALOG CIRCUIT, PQCC44 |
| LIS3L02AQ3 | SPECIALTY ANALOG CIRCUIT, PQCC44 |
| LIS3L06AL | SPECIALTY ANALOG CIRCUIT, PBGA8 |
| LIS3LV02DQ-TR | SPECIALTY ANALOG CIRCUIT, PQCC28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LIS35DETR | 功能描述:加速计 - 板上安装 DGTL OUTPT MTN SEN MEMS ULTRA LO PWR RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS-3-6 | 制造商:TDK-Lambda Corporation 功能描述:15W AC To DC Switching Power Supply - 95-132V/187-265V in - 6V 2.5A out |
| LIS3DETR | 制造商:STMicroelectronics 功能描述: 制造商:STMicroelectronics 功能描述:SADA_MEMS digital output motion sensor, ultra low-power high performance 3-axes |
| LIS3DH | 功能描述:加速计 - 板上安装 MEMS Ultra Low-Power 3-Axes "Nano" RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS3DHHTR | 功能描述:ACCELEROMETER 3-AXIS 16LGA 制造商:stmicroelectronics 系列:MEMS 零件状态:在售 类型:数字 轴:X，Y，Z 加速度范围:±2.5g 灵敏度（LSB/g）:13157（±2.5g） 灵敏度（mV/g）:- 带宽:235Hz ~ 440Hz 输出类型:SPI 电压 - 电源:1.71 V ~ 3.6 V 特性:温度传感器 工作温度:-40°C ~ 85°C（TA） 安装类型:表面贴装 封装/外壳:16-LGA 供应商器件封装:16-CCLGA（5x5） 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。