- 您现在的位置：买卖IC网 > PDF目录98000 > LIS35DETR (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PBGA14 PDF资料下载
参数资料
| 型号： | LIS35DETR |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PBGA14 |
| 封装： | 3 X 5 MM, 0.92 MM HEIGHT, 0.80 MM PITCH, GREEN, PLASTIC, LGA-14 |
| 文件页数： | 9/39页 |
| 文件大小： | 650K |
| 代理商： | LIS35DETR |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
LIS35DE
Digital interfaces
Doc ID 15594 Rev 1
17/39
5
Digital interfaces
The registers embedded inside the LIS35DE may be accessed through both the I2C and
SPI serial interfaces. The latter may be SW configured to operate either in 3-wire or 4-wire
interface mode.
The serial interfaces are mapped onto the same pads. To select/exploit the I2C interface, CS
line must be tied high (i.e connected to Vdd_IO).
5.1
I2C serial interface
The LIS35DE I2C is a bus slave. The I2C is employed to write the data into the registers
whose content can also be read back.
The relevant I2C terminology is given in the table below.
There are two signals associated with the I2C bus: the Serial Clock Line (SCL) and the
Serial DAta line (SDA). The latter is a bidirectional line used for sending and receiving the
data to/from the interface. Both the lines are connected to Vdd_IO through a pull-up resistor
embedded inside the LIS35DE. When the bus is free both the lines are high.
The I2C interface is compliant with fast mode (400 kHz) I2C standards as well as the normal
mode.
Table 8.
Serial interface pin description
PIN Name
PIN description
CS
SPI enable
I2C/SPI mode selection (1: I2C mode; 0: SPI enabled)
SCL/SPC
I2C serial clock (SCL)
SPI Serial port clock (SPC)
SDA/SDI/SDO
I2C serial data (SDA)
SPI serial data input (SDI)
3-wire interface serial data output (SDO)
SDO
SPI serial data output (SDO)
Table 9.
Serial interface pin description
Term
Description
Transmitter
The device which sends data to the bus
Receiver
The device which receives data from the bus
Master
The device which initiates a transfer, generates clock signals and terminates a
transfer
Slave
The device addressed by the master
相关PDF资料 |
PDF描述 |
|---|---|
| LIS3L02AQ3TR | SPECIALTY ANALOG CIRCUIT, PQCC44 |
| LIS3L02AQ3 | SPECIALTY ANALOG CIRCUIT, PQCC44 |
| LIS3L06AL | SPECIALTY ANALOG CIRCUIT, PBGA8 |
| LIS3LV02DQ-TR | SPECIALTY ANALOG CIRCUIT, PQCC28 |
| LIS3LV02DQ | SPECIALTY ANALOG CIRCUIT, PQCC28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LIS-3-6 | 制造商:TDK-Lambda Corporation 功能描述:15W AC To DC Switching Power Supply - 95-132V/187-265V in - 6V 2.5A out |
| LIS3DETR | 制造商:STMicroelectronics 功能描述: 制造商:STMicroelectronics 功能描述:SADA_MEMS digital output motion sensor, ultra low-power high performance 3-axes |
| LIS3DH | 功能描述:加速计 - 板上安装 MEMS Ultra Low-Power 3-Axes "Nano" RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS3DHHTR | 功能描述:ACCELEROMETER 3-AXIS 16LGA 制造商:stmicroelectronics 系列:MEMS 零件状态:在售 类型:数字 轴:X，Y，Z 加速度范围:±2.5g 灵敏度（LSB/g）:13157（±2.5g） 灵敏度（mV/g）:- 带宽:235Hz ~ 440Hz 输出类型:SPI 电压 - 电源:1.71 V ~ 3.6 V 特性:温度传感器 工作温度:-40°C ~ 85°C（TA） 安装类型:表面贴装 封装/外壳:16-LGA 供应商器件封装:16-CCLGA（5x5） 标准包装:1 |
| LIS3DHTR | 功能描述:加速计 - 板上安装 MEMS Ultra Low-Power 3-Axes "Nano" RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
发布紧急采购，3分钟左右您将得到回复。