参数资料
型号: LIS3L02AQ5TR
厂商: STMICROELECTRONICS
元件分类: 模拟信号调理
英文描述: SPECIALTY ANALOG CIRCUIT, PQCC44
封装: 7 X 7 MM, QFN-44
文件页数: 2/15页
文件大小: 213K
代理商: LIS3L02AQ5TR
Obsolete
Product(s)
- Obsolete
Product(s)
3 Functionality
LIS3L02AQ5
10/15
CD00059677
3
Functionality
The LIS3L02AQ5 is a high performance, low-power, analog output 3-axis linear accelerometer
packaged in a QFN package. The complete device includes a sensing element and an IC
interface able to take the information from the sensing element and to provide an analog signal
to the external world.
3.1
Sensing element
A proprietary process is used to create a surface micro-machined accelerometer. The
technology allows to carry out suspended silicon structures which are attached to the substrate
in a few points called anchors and are free to move in the direction of the sensed acceleration.
To be compatible with the traditional packaging techniques a cap is placed on top of the
sensing element to avoid blocking the moving parts during the moulding phase of the plastic
encapsulation.
When an acceleration is applied to the sensor the proof mass displaces from its nominal
position, causing an imbalance in the capacitive half-bridge. This imbalance is measured using
charge integration in response to a voltage pulse applied to the sense capacitor.
At steady state the nominal value of the capacitors are few pF and when an acceleration is
applied the maximum variation of the capacitive load is up to 100fF.
3.2
IC Interface
In order to increase robustness and immunity against external disturbances the complete signal
processing chain uses a fully differential structure. The final stage converts the differential
signal into a single-ended one to be compatible with the external world.
The signals of the sensing element are multiplexed and fed into a low-noise capacitive charge
amplifier that implements a Correlated Double Sampling system (CDS) at its output to cancel
the offset and the 1/f noise. The output signal is de-multiplexed and transferred to three
different S&Hs, one for each channel and made available to the outside.
The low noise input amplifier operates at 200 kHz while the three S&Hs operate at a sampling
frequency of 66 kHz. This allows a large oversampling ratio, which leads to in-band noise
reduction and to an accurate output waveform.
All the analog parameters (zero-g level, sensitivity and self-test) are ratiometric to the supply
voltage. Increasing or decreasing the supply voltage, the sensitivity and the offset will increase
or decrease almost linearly. The self test voltage change varies cubically with the supply
voltage.
3.3
Factory calibration
The IC interface is factory calibrated for sensitivity (So) and Zero-g level (Voff).
The trimming values are stored inside the device by a non volatile structure. Any time the
device is turned on, the trimming parameters are downloaded into the registers to be employed
during the normal operation. This allows the user to employ the device without further
calibration.
相关PDF资料
PDF描述
LIS3L02AQ5 SPECIALTY ANALOG CIRCUIT, PQCC44
LIS3L02AQ SPECIALTY ANALOG CIRCUIT, QCC44
LIS3L02DQ-TR SPECIALTY ANALOG CIRCUIT, QCC44
LIS3L02DQ SPECIALTY ANALOG CIRCUIT, QCC44
LIT1108CS8-5#PBF 1.5 A SWITCHING REGULATOR, 25 kHz SWITCHING FREQ-MAX, PDSO8
相关代理商/技术参数
参数描述
LIS3L02AQ-TR 功能描述:ACCELEROMETER TRPL AXIS 44QFN RoHS:是 类别:传感器,转换器 >> 加速计 系列:- 标准包装:1 系列:SCA1000 轴:X,Y 加速范围:±1.7g 灵敏度:1.2V/g 电源电压:4.75 V ~ 5.25 V 输出类型:数字 带宽:50±30Hz 接口:SPI 安装类型:表面贴装 封装/外壳:12-SMD 供应商设备封装:12-SMD 其它名称:551-1007-1
LIS3L02AS 制造商:STMicroelectronics 功能描述:ACCELEROMETER TRIPLE 2G/ 6G 3V TO 5.25V 24SOIC - Bulk
LIS3L02AS4 功能描述:ACCELEROMETER TRPL AXIS 24SOIC RoHS:否 类别:传感器,转换器 >> 加速计 系列:- 标准包装:1 系列:SCA1000 轴:X,Y 加速范围:±1.7g 灵敏度:1.2V/g 电源电压:4.75 V ~ 5.25 V 输出类型:数字 带宽:50±30Hz 接口:SPI 安装类型:表面贴装 封装/外壳:12-SMD 供应商设备封装:12-SMD 其它名称:551-1007-1
LIS3L02AS5 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:MEMS INERTIAL SENSOR: 3-axis - 【2g/6g LINEAR ACCELEROMETER
LIS3L02AS5TR 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:MEMS INERTIAL SENSOR: 3-axis - 【2g/6g LINEAR ACCELEROMETER