- 您现在的位置：买卖IC网 > PDF目录69004 > LIS3L02AS5TR (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PDSO24 PDF资料下载
参数资料
| 型号： | LIS3L02AS5TR |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO24 |
| 封装： | LEAD FREE, SOP-24 |
| 文件页数： | 13/14页 |
| 文件大小： | 157K |
| 代理商： | LIS3L02AS5TR |
2 Mechanical and Electrical Specifications
LIS3L02AS5
8/14
Self Test allows to test the mechanical and electric part of the sensor, allowing the seismic
mass to be moved by means of an electrostatic test-force. The Self Test function is off when the
ST pin is connected to GND. When the ST pin is tied at Vdd an actuation force is applied to the
sensor, simulating a definite input acceleration. In this case the sensor outputs will exhibit a
voltage change in their DC levels which is related to the selected full scale and depending on
the Supply Voltage through the device sensitivity. When ST is activated, the device output level
is given by the algebraic sum of the signals produced by the acceleration acting on the sensor
and by the electrostatic test-force. If the output signals change within the amplitude specified
inside Table 2, than the sensor is working properly and the parameters of the interface chip are
within the defined specification
Output impedance describes the resistor inside the output stage of each channel. This
resistor is part of a filter consisting of an external capacitor of at least 320pF and the internal
resistor. Due to the high resistor level only small, inexpensive external capacitors are needed to
generate low corner frequencies. When interfacing with an ADC it is important to use high input
impedance input circuitries to avoid measurement errors. Note that the minimum load
capacitance forms a corner frequency beyond the resonance frequency of the sensor. For a flat
frequency response a corner frequency well below the resonance frequency is recommended.
In general the smallest possible bandwidth for an particular application should be chosen to get
the best results.
相关PDF资料 |
PDF描述 |
|---|---|
| LIS3L02DS | SPECIALTY ANALOG CIRCUIT, PDSO24 |
| LIS3LV02DL | SPECIALTY ANALOG CIRCUIT, PBGA16 |
| LM10010SD | SWITCHING REGULATOR, PDSO10 |
| LM10010SDX | SWITCHING REGULATOR, PDSO10 |
| LM12L458CIVX | SPECIALTY ANALOG CIRCUIT, PQCC44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LIS3L02DQ | 功能描述:加速计 - 板上安装 2-axis +/-2g Digital MEMS Intertial Sensr RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS3L02DQ-TR | 功能描述:ACCELEROMETER TRPL AXIS 44QFN RoHS:是 类别:传感器，转换器 >> 加速计 系列:- 标准包装:1 系列:SCA1000 轴:X，Y 加速范围:±1.7g 灵敏度:1.2V/g 电源电压:4.75 V ~ 5.25 V 输出类型:数字 带宽:50±30Hz 接口:SPI 安装类型:表面贴装 封装/外壳:12-SMD 供应商设备封装:12-SMD 其它名称:551-1007-1 |
| LIS3L02DS | 制造商:STMicroelectronics 功能描述: |
| LIS3L06AL | 功能描述:加速计 - 板上安装 3-axis +/-2g/+/-6g MEMS Intertial Sensr RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS3L06AL_06 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:MEMS INERTIAL SENSOR-3-axis - +/-2g/6g ultracompact linear accelerometer |
发布紧急采购，3分钟左右您将得到回复。