- 您现在的位置：买卖IC网 > PDF目录79714 > LK1001-9RT (POWER-ONE INC) 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | LK1001-9RT |
| 厂商： | POWER-ONE INC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| 封装： | HEAT SINK, METAL, CASE K02, MODULE |
| 文件页数： | 25/26页 |
| 文件大小： | 1027K |
| 代理商： | LK1001-9RT |
Cassette Style
AC-DC Converters
K Series
Edition 5/5.2000
8/26
Thermal Considerations
If a converter is located in free, quasi-stationary air (con-
vection cooling) at the indicated maximum ambient tem-
perature
TA max (see table: Temperature specifications) and
is operated at its nominal input voltage and output power,
the temperature measured at the
Measuring point of case
temperature TC (see: Mechanical Data) will approach the
indicated value
TC max after the warm-up phase. However,
the relationship between
TA and TC depends heavily on the
conditions of operation and integration into a system. The
thermal conditions are influenced by input voltage, output
current, airflow and temperature of surrounding compo-
nents and surfaces.
TA max is therefore, contrary to TC max,
an indicative value only.
Caution: The installer must ensure that under all operat-
ing conditions
TC remains within the limits stated in the
table:
Temperature specifications.
Notes: Sufficient forced cooling or an additional heat sink
allows
TA to be higher than 71
°C (e.g. 85°C) if T
C max is not
exceeded.
For -7 or -9 units at an ambient temperature
TA of 85°C with
only convection cooling, the maximum permissible current
for each output is approx. 40% of its nominal value as per
figure.
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
50
60
70
80
90
100
Io/Io nom
TA [°C]
0.9
1.0
Forced cooling
05089
TA min
TC max
Convection cooling
Fig. 7
Output current derating versus temperature for –7 and –9.
Thermal Protection
A temperature sensor generates an internal inhibit signal
which disables the outputs if the case temperature exceeds
TC max. The outputs are automatically re-enabled if the tem-
perature drops below this limit.
It is recommended that continuous operation under simul-
taneous extreme worst case conditions of the following
three parameters be avoided: Minimum input voltage,
maximum output power and maximum temperature.
Output Protection
Each output is protected against overvoltage which could
occur due to a failure of the control circuit by means of a
voltage suppressor diode which, under worst case condi-
tions, may become a short circuit. The suppressor diodes
are not designed to withstand externally applied over-
voltages. Overload at any of the two outputs will cause a
shut-down of both outputs. A red LED indicates the over-
load condition.
Uo1d
t d
Ur
t
Uo2d
<10
s
<10
s
Uo1
Uo2
Io1/Io1 nom
0
0.5
1
Io2/Io2 nom
05072
Fig. 8
Control deviation of uo1/2 d vs. dynamic load change.
Output Voltage Regulation of Single or Double Output
Modules with Outputs1 and 2 Connected in Series
Uo
Uo nom
0.98
0.5
0
0.5
1.0
Io1
IoL
Io
Io nom
05068
Fig. 9
Uo1 versus Io1 (typ.) of single output units
Parallel or Series Connection of Units
Single or double output units with equal nominal output volt-
age can be connected in parallel without any precautions
using option T.
With option T (current sharing), all units share the current
approximately equally.
Single output units and/or main and second outputs of dou-
ble output units can be connected in series with any other
(similar) output.
Note:
– Parallel connection of double output units should always
include both, main and second output to maintain good
regulation of both outputs.
– Not more than 5 units should be connected in parallel.
– Series connection of second outputs without involving
their main outputs should be avoided as regulation may
be poor.
– The maximum output current is limited by the output with
the lowest current limitation if several outputs are con-
nected in series.
相关PDF资料 |
PDF描述 |
|---|---|
| LK1001-9TB2 | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LK1001-9 | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LK1301-7ED4B2 | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LK1301-7EPD0B1 | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LK1301-7EPD0T | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LK100-24P | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic |
| LK100-28P | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic |
| LK10051R0K-T | 功能描述:固定电感器 INDCTR STD MULTILYR 0402 1uH 10% RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm |
| LK10051R0K-T | 制造商:TAIYO YUDEN 功能描述:Inductor Series:LF LK |
| LK10051R0K-TV | 功能描述:FIXED IND 1UH 20MA 640 MOHM SMD 制造商:taiyo yuden 系列:LK 包装:剪切带（CT） 零件状态:在售 类型:多层 材料 - 磁芯:- 电感:1μH 容差:±10% 额定电流:20mA 屏蔽:无屏蔽 DC 电阻（DCR）:640 毫欧 不同频率时的 Q 值:20 @ 10MHz 频率 - 自谐振:60MHz 等级:AEC-Q200 工作温度:-40°C ~ 85°C 频率 - 测试:10MHz 安装类型:表面贴装 封装/外壳:0402（1005 公制） 供应商器件封装:0402（1005 公制） 大小/尺寸:0.039" 长 x 0.020" 宽（1.00mm x 0.50mm） 高度 - 安装（最大值）:0.022"（0.55mm） 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。