- 您现在的位置：买卖IC网 > PDF目录67755 > LM20323AMHE (NATIONAL SEMICONDUCTOR CORP) 6 A SWITCHING REGULATOR, 570 kHz SWITCHING FREQ-MAX, PDSO20 PDF资料下载
参数资料
| 型号： | LM20323AMHE |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 6 A SWITCHING REGULATOR, 570 kHz SWITCHING FREQ-MAX, PDSO20 |
| 封装： | TSSOP-20 |
| 文件页数： | 8/20页 |
| 文件大小： | 492K |
| 代理商： | LM20323AMHE |
30077287
FIGURE 10. Thermal Resistance vs PCB Area (4 Layer
Board)
PCB LAYOUT CONSIDERATIONS
PC board layout is an important part of DC-DC converter de-
sign. Poor board layout can disrupt the performance of a DC-
DC converter and surrounding circuitry by contributing to EMI,
ground bounce, and resistive voltage loss in the traces. These
can send erroneous signals to the DC-DC converter resulting
in poor regulation or instability.
Good layout can be implemented by following a few simple
design rules.
1. Minimize area of switched current loops. In a buck regulator
there are two loops where currents are switched at high slew
rates. The first loop starts from the input capacitor, to the reg-
ulator VIN pin, to the regulator SW pin, to the inductor then
out to the output capacitor and load. The second loop starts
from the output capacitor ground, to the regulator GND pins,
to the inductor and then out to the load (see Figure 11). To
minimize both loop areas the input capacitor should be placed
as close as possible to the VIN pin. Grounding for both the
input and output capacitor should consist of a small localized
top side plane that connects to GND and the exposed pad
(EP). The inductor should be placed as close as possible to
the SW pin and output capacitor.
2. Minimize the copper area of the switch node. Since the
LM20323A has the SW pins on opposite sides of the package
it is recommended that the SW pins should be connected with
a trace that runs around the package. The inductor should be
placed at an equal distance from the SW pins using 100 mil
wide traces to minimize capacitive and conductive losses.
3. Have a single point ground for all device grounds located
under the EP. The ground connections for the compensation,
feedback, and soft-start components should be connected
together then routed to the EP pin of the device. The AGND
pin should connect to GND under the EP. If not properly han-
dled poor grounding can result in degraded load regulation or
erratic switching behavior.
4. Minimize trace length to the FB pin. Since the feedback
node can be high impedance the trace from the output resistor
divider to FB pin should be as short as possible. This is most
important when high value resistors are used to set the output
voltage. The feedback trace should be routed away from the
SW pin and inductor to avoid contaminating the feedback sig-
nal with switch noise.
5. Make input and output bus connections as wide as possi-
ble. This reduces any voltage drops on the input or output of
the converter and can improve efficiency. Voltage accuracy
at the load is important so make sure feedback voltage sense
is made at the load. Doing so will correct for voltage drops at
the load and provide the best output accuracy.
6. Provide adequate device heatsinking. For most 3A designs
a four layer board is recommended. Use as many vias as is
possible to connect the EP to the power plane heatsink. For
best results use a 5x4 via array with a minimum via diameter
of 12 mils. "Via tenting" with the solder mask may be neces-
sary to prevent wicking of the solder paste applied to the EP.
See the Thermal Considerations section to ensure enough
copper heatsinking area is used to keep the junction temper-
ature below 125°C.
30077246
FIGURE 11. Schematic of LM20323A Highlighting Layout Sensitive Nodes
www.national.com
16
LM20323A
相关PDF资料 |
PDF描述 |
|---|---|
| LM20323AMH | 6 A SWITCHING REGULATOR, 570 kHz SWITCHING FREQ-MAX, PDSO20 |
| LM22677QTJ-5.0 | 8.75 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PSSO7 |
| LM22677QTJE-5.0 | 8.75 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PSSO7 |
| LM22677QTJ-ADJ | 8.75 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PSSO7 |
| LM2585-5.0MDC | 7 A SWITCHING REGULATOR, 125 kHz SWITCHING FREQ-MAX, UUC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM20323AMHX | 制造商:NSC 制造商全称:National Semiconductor 功能描述:36V, 3A 500 kHz Synchronous Buck Regulator |
| LM20323EVAL | 功能描述:电源管理IC开发工具 LM20323 EVAL BOARD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| LM20323MH | 制造商:Texas Instruments 功能描述:Conv DC-DC Single Step Down 4.5V to 36V 20-Pin TSSOP EP Rail 制造商:Texas Instruments 功能描述:BUCK REG, 3A, 4V/36V, POWERWISE, 20TSSOP 制造商:Texas Instruments 功能描述:IC, DC-DC CONV; Primary Input Voltage:36V; No. of Outputs:1; Output Voltage:32V; Output Current:3A; No. of Pins:20; Operating Temperature Min:-40C; Operating Temperature Max:125C; Operating Temperature Range:-40C to +125C ;RoHS Compliant: Yes |
| LM20323MH/NOPB | 功能描述:直流/直流开关转换器 36V,3A 500 KHZ SYNC BUCK REG RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| LM20323MHE | 制造商:Texas Instruments 功能描述:Conv DC-DC Single Step Down 4.5V to 36V 20-Pin TSSOP EP T/R |
发布紧急采购，3分钟左右您将得到回复。