- 您现在的位置：买卖IC网 > PDF目录30745 > LM2202M/NOPB (NATIONAL SEMICONDUCTOR CORP) 1 CHANNEL, VIDEO AMPLIFIER, PDSO20 PDF资料下载
参数资料
| 型号： | LM2202M/NOPB |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 1 CHANNEL, VIDEO AMPLIFIER, PDSO20 |
| 封装： | M20B |
| 文件页数： | 17/17页 |
| 文件大小： | 416K |
| 代理商： | LM2202M/NOPB |
Circuit Description (Continued)
DRIVE CONTROL SECTION
A simplified schematic of the LM2202’s drive control section
is shown in
Figure 6. A 0V to 4V DC voltage is applied at the
drive control input (pin 9). Transistors Q49, Q50 and Q54
buffer and level shift the contrast voltage to the base of Q56.
The voltage at the emitter of Q56 equals the drive voltage,
V
drive and the current through Q56’s collector is given by
I
C56 = Vdrive/R43.
Transistor Q56’s collector current is used to unbalance the
current through the differential pair comprised of Q58 and
Q60. Q60’s base is internally biased at 7.3V and connected
to the base of Q12 (see
Figure 3). Q58’s base is internally
connected to the base of Q11 (see
Figure 3). With V
cont =
2V, the differential pair (Q58, Q60) is balanced and the volt-
age at the bases of Q11 and Q12 is 7.3V. Under this condi-
tion, Q10’s collector current is equally split between Q11 and
Q12 (see
Figure 3). If the drive voltage at pin 9 is greater
than 2V then Q56’s collector current increases, thus pulling
Q58’s collector node lower and consequently moving Q58’s
base below 7.3V. With base of Q11 below 7.3V, current
through Q12 (see
Figure 3) increases and the amplifier’s
gain increases. With V
drive = 4V, the amplifier’s gain is maxi-
mum under maximum contrast condition (i.e., V
cont = 4V).
If the drive voltage at pin 8 is less than 2V then Q56’s collec-
tor current decreases and Q58’s base is pulled above 7.3V.
With base of Q11 greater than 7.3V, less current flows
through Q12 (see
Figure 3), consequently the amplifier’s
gain decreases. With V
drive = 0V, the amplifier’s gain is 6 dB
less than the maximum gain.
CLAMP GATE AND CLAMP COMPARATOR SECTION
Figure 7 and Figure 8 show simplified schematics of the
clamp gate and clamp comparator circuits. The clamp gate
circuit (
Figure 7) consists of a PNP input buffer transistor
(Q82), a PNP emitter coupled pair (Q85 and Q86) refer-
enced on one side to 2.1V and an output switch transistor
Q89. When the clamp gate input at pin 14 is high (> 1.5V)
the Q89 switch is on and shunts the 200 A current from cur-
rent source Q90 to ground. When pin 14 is low (< 1.3V) the
Q89 switch is off and the 200 A current is mirrored by the
current mirror comprised of Q91 and Q75 (see
Figure 8).
Consequently the clamp comparator comprised of the differ-
ential pair Q74 and Q77 is enabled. The input of the clamp
comparator is similar to the clamp gate except that an NPN
emitter coupled pair is used to control the current that will
charge or discharge the clamp capacitor externally con-
nected from pin 12 to ground. PNP transistors are used at
the inputs because they offer a number of advantages over
NPNs. PNPs will operate with base voltages at or near
ground and will usually have a greater emitter base break-
down voltage (BVebo). Because the differential input voltage
to the clamp comparator during the video scan period could
be greater than the BVebo of NPN transistors, a resistor
(R63) with a value one half that of R60 or R68 is connected
between the bases of Q71 and Q79. The clamp compara-
tor’s common mode range is from ground to approximately
9V and the maximum differential input voltage is V
CC.
www.national.com
9
相关PDF资料 |
PDF描述 |
|---|---|
| LM22672QMR-ADJ | 1.8 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDSO8 |
| LM236ZT | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.49 V, PBCY3 |
| LM236DT | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.49 V, PDSO8 |
| LM236Z-AP | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.49 V, PBCY3 |
| LM336Z | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.49 V, PBCY3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM2202MX | 功能描述:IC VIDEO AMP SYS 230MHZ 20-SOIC RoHS:否 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
| LM2202N | 功能描述:IC VIDEO AMP SYSTEM 20-DIP RoHS:否 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
| LM220K12 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| LM220K15 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| LM220K5 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
发布紧急采购，3分钟左右您将得到回复。