- 您现在的位置：买卖IC网 > PDF目录1820 > LM22674MR-5.0/NOPB (National Semiconductor)IC REG BUCK 5V 0.5A 8PSOP PDF资料下载
参数资料
| 型号： | LM22674MR-5.0/NOPB |
| 厂商： | National Semiconductor |
| 文件页数： | 7/22页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 5V 0.5A 8PSOP |
| 产品培训模块： | SIMPLE SWITCHER® Regulators LM315x & LM2267x SIMPLE SWITCHER® and WEBENCH |
| 标准包装： | 95 |
| 系列： | SIMPLE SWITCHER® |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 5V |
| 输入电压： | 4.5 V ~ 42 V |
| PWM 型： | 电压模式 |
| 频率 - 开关： | 500kHz |
| 电流 - 输出： | 500mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm Width）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 8-PSOP-EP |
| 配用： | 551600236-001-ND - WEBENCH BUILD IT LM2267X 8-PSOP |
| 其它名称： | LM22674MR-5.0 LM22674MR-5.0-ND |
SNVS590L – SEPTEMBER 2008 – REVISED APRIL 2013
Although an internal pull-up is provided on the EN pin, it is good practice to pull the input high, when this feature
is not used, especially in noisy environments. This can most easily be done by connecting a resistor between
VIN and the EN pin. The resistor is required, since the internal zener diode, at the EN pin, will conduct for
voltages above about 6V. The current in this zener must be limited to less than 100 μA. A resistor of 470 k ? will
limit the current to a safe value for input voltages as high 42V. Smaller values of resistor can be used at lower
input voltages.
The LM22674 also incorporates an input under voltage lock-out (UVLO) feature. This prevents the regulator from
turning on when the input voltage is not great enough to properly bias the internal circuitry. The rising threshold is
4.3V (typ.) while the falling threshold is 3.9V (typ.). In some cases these thresholds may be too low to provide
good system performance. The solution is to use the EN input as an external UVLO to disable the part when the
input voltage falls below a lower boundary. This is often used to prevent excessive battery discharge or early
turn-on during start-up. This method is also recommended to prevent abnormal device operation in applications
where the input voltage falls below the minimum of 4.5V. Figure 12 shows the connections to implement this
method of UVLO. The following equations can be used to determine the correct resistor values:
(1)
where
?
V off is the input voltage where the regulator shuts off, and V on is the voltage where the regulator turns on.
(2)
Due to the 6 μA pull-up, the current in the divider should be much larger than this. A value of 20 k ? , for R ENB is a
good first choice. Also, a zener diode may be needed between the EN pin and ground, in order to comply with
the absolute maximum ratings on this pin.
V in
R ENT
EN
R ENB
Figure 12. External UVLO Connections
Duty Cycle Limits
Ideally the regulator would control the duty cycle over the full range of zero to one. However due to inherent
delays in the circuitry, there are limits on both the maximum and minimum duty cycles that can be reliably
controlled. This in turn places limits on the maximum and minimum input and output voltages that can be
converted by the LM22674. A minimum on-time is imposed by the regulator in order to correctly measure the
switch current during a current limit event. A minimum off-time is imposed in order the re-charge the bootstrap
capacitor. The following equation can be used to determine the approximate maximum input voltage for a given
output voltage:
where
?
F sw is the switching frequency and T ON is the minimum on-time; both found in the Electrical Characteristics
table.
(3)
The worst case occurs at the lowest output voltage. If the input voltage, found in the above equation, is
exceeded, the regulator will skip cycles, effectively lowering the switching frequency. The consequences of this
are higher output voltage ripple and a degradation of the output voltage accuracy.
Copyright ? 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM22674
7
相关PDF资料 |
PDF描述 |
|---|---|
| LM2574BN | IC REG BUCK ADJ 0.5A 8DIP |
| LM2574N-ADJ | IC REG BUCK ADJ 0.5A 8DIP |
| LM2575BWM TR | IC REG BUCK ADJ 1A 24SOIC |
| LM2576BU TR | IC REG BUCK ADJ 3A TO263-5 |
| LM2588T-12/NOPB | IC REG MULTI CONFIG 12V TO220-7 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM22674MR-ADJ | 制造商:Texas Instruments 功能描述:REGULATOR, ADJ. VOLTAGE, 0.5A 8PSOP 制造商:Texas Instruments 功能描述:REGULATOR, ADJ. VOLTAGE, 0.5A 8PSOP; Primary Input Voltage:42V; No. of Outputs:1; Output Current:500mA; Voltage Regulator Case Style:SOP; No. of Pins:8; Operating Temperature Min:-40C; Operating Temperature Max:125C; SVHC:No SVHC ;RoHS Compliant: Yes |
| LM22674MR-ADJ/NOPB | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| LM22674MRE-5.0 | 制造商:Texas Instruments 功能描述:SIMPLESWITCH 5.0V 4.5~42VIN 8PSOP 制造商:Texas Instruments 功能描述:SIMPLESWITCH, 5.0V 4.5~42VIN, 8PSOP 制造商:Texas Instruments 功能描述:SIMPLESWITCH, 5.0V 4.5~42VIN, 8PSOP, Primary Input Voltage:12V, No. of Outputs:1 |
| LM22674MRE-5.0/NOPB | 功能描述:直流/直流开关转换器 500MA,STEP-DOWN VLTG REG RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| LM22674MRE-5.0/NOPB | 制造商:Texas Instruments 功能描述:Switching Regulator IC |
发布紧急采购，3分钟左右您将得到回复。