- 您现在的位置：买卖IC网 > PDF目录67755 > LM22677QTJ-5.0 (NATIONAL SEMICONDUCTOR CORP) 8.75 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PSSO7 PDF资料下载
参数资料
| 型号： | LM22677QTJ-5.0 |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 8.75 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PSSO7 |
| 封装： | PLASTIC, TO-263, 7 PIN |
| 文件页数： | 15/16页 |
| 文件大小： | 398K |
| 代理商： | LM22677QTJ-5.0 |
30074150
FIGURE 2. Output Current in Foldback vs.
Nominal Duty Cycle
The percentage of output current limit fold back is affected by
duty
cycle,
inductance,
and
switching
frequency.
See Figure 2 for details.
The current limit will only protect the inductor from a runaway
condition if the LM22677 is operating in its safe operating
area. A runaway condition of the inductor is potentially catas-
trophic to the application. For every design, the safe operating
area needs to be calculated. Factors in determining the safe
operating area are the switching frequency, input voltage,
output voltage, minimum on-time and feedback voltage dur-
ing an over current condition.
As a first pass check, if the following equation holds true, a
given design is considered in a safe operating area and the
current limit will protect the circuit:
V
IN x TBLK x F < VOUT x 0.724
If the equation above does not hold true, the following sec-
ondary equation will need to hold true to be in safe operating
area:
If both equations do not hold true, a particular design will not
have an effective current limit function which might damage
the circuit during startup, over current conditions, or steady
state over current and short circuit condition. Oftentimes a
reduction of the maximum input voltage or a reduction of the
switching frequency will bring a design into the safe operating
area.
When synchronized to an external sync pulse, the LM22677
will not fold back the switching frequency in an over current
condition.
Soft-Start
The soft-start feature allows the regulator to gradually reach
the initial steady state operating point, thus reducing start-up
stresses and surges. The soft-start is fixed to 500 s (typical)
start-up time and cannot be modified.
Switching Frequency Setting and
Synchronization
There are three different modes for the RT/SYNC pin. It can
be left floating for a 500 kHz switching frequency.
A resistor from the RT/SYNC pin to ground can be used to
adjust the switching frequency between 200 kHz and 1 MHz.
An external synchronization pulse can be applied to the RT/
SYNC pin for switching frequencies up to 1 MHz. The syn-
chronizing frequency must be greater than the internal switch-
ing frequency for proper operation. The maximum internal
switching frequency is guaranteed in the Electrical Charac-
teristics table. The LM22677 internally sets the RT/SYNC
mode during start up.
Many applications are limited to lower switching frequencies
due to minimum on-time and minimum off-time requirements
as well as increased switching losses at switching frequen-
cies higher than 500 kHz. In case of synchronizing to an
external sync pulse, the clock pulse must be in a valid low or
high state when the LM22677 starts up and can be applied
after device regulation. The internal oscillator will synchronize
to the external sync pulse rising edge. If the external sync
pulse is disconnected the LM22677 switching frequency will
return to default 500 kHz (typ.).
When operating at frequencies above 500 kHz, external com-
ponents such as the inductor and the output capacitors can-
not be reduced dramatically. This is due to the fixed internal
compensation and stability requirements. Running the
LM22677 at frequencies higher than 500 kHz is intended for
applications with EMI or beat frequency concerns. The flexi-
bility of increasing the switching frequency above 500 kHz can
be used to operate outside a critical signal frequency band of
an application. This can also be used to set multiple switchers
in an application to the same frequency to reduce beat fre-
quencies and simplify filtering.
See the current limit section of this datasheet for information
about the safe operating area. When synchronizing to an ex-
ternal synchronization pulse, the LM22677 will not fold back
the switching frequency in an over current condition.
The typical curve below shows adjusted switching frequen-
cies with different frequency set resistors from the RT/SYNC
pin to ground.
30074113
FIGURE 3. Switching Frequency vs RT/SYNC Resistor
www.national.com
8
LM22677/LM22677Q
相关PDF资料 |
PDF描述 |
|---|---|
| LM22677QTJE-5.0 | 8.75 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PSSO7 |
| LM22677QTJ-ADJ | 8.75 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PSSO7 |
| LM2585-5.0MDC | 7 A SWITCHING REGULATOR, 125 kHz SWITCHING FREQ-MAX, UUC |
| LM2585-5.0MWC | 7 A SWITCHING REGULATOR, 125 kHz SWITCHING FREQ-MAX, UUC |
| LM2585-12MDC | 7 A SWITCHING REGULATOR, 125 kHz SWITCHING FREQ-MAX, UUC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM22677QTJ-ADJ | 制造商:NSC 制造商全称:National Semiconductor 功能描述:5A SIMPLE SWITCHER?, Step-Down Voltage Regulator with Synchronization or Adjustable Switching Frequency |
| LM22677QTJ-ADJ/NOPB | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| LM22677QTJE-5.0 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:5A SIMPLE SWITCHER?, Step-Down Voltage Regulator with Synchronization or Adjustable Switching Frequency |
| LM22677QTJE-5.0/NOPB | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| LM22677QTJE-ADJ | 制造商:NSC 制造商全称:National Semiconductor 功能描述:5A SIMPLE SWITCHER?, Step-Down Voltage Regulator with Synchronization or Adjustable Switching Frequency |
发布紧急采购，3分钟左右您将得到回复。