- 您现在的位置：买卖IC网 > PDF目录98000 > LM25066APSQE (NATIONAL SEMICONDUCTOR CORP) POWER SUPPLY SUPPORT CKT, QCC24 PDF资料下载
参数资料
| 型号： | LM25066APSQE |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 电源管理 |
| 英文描述： | POWER SUPPLY SUPPORT CKT, QCC24 |
| 封装： | LLP-24 |
| 文件页数： | 28/48页 |
| 文件大小： | 1658K |
| 代理商： | LM25066APSQE |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
Manufacturer Specific PMBus
Commands
MFR_SPECIFIC_00: READ_VAUX (D0h)
The READ_VAUX command will report the 12-bit ADC mea-
sured auxiliary voltage. Voltages greater than or equal to
1.16V to ground will be reported at plus full scale (0FFFh).
Voltages less than or equal to 0V referenced to ground will be
reported as 0 (0000h). Coefficients for the VAUX value are
dependent on the value of the external divider (if used). To
read data from the MFR_READ_VAUX command, use the
PMBus Read Word protocol.
TABLE 22. MFR_READ_VAUX Register
Value
Meaning
Default
0h – 0FFFh
Measured value
for VAUX input
0000h
MFR_SPECIFIC_01: MFR_READ_IIN (D1h)
The MFR_READ_IIN command will report the 12-bit ADC
measured current sense voltage. To read data from the
MFR_READ_IIN command, use the PMBus Read Word
protocol. Reading this register should use the coefficients
shown in the Telemetry and Warning Conversion Coefficients
Table. Please see the section on coefficient calculations to
calculate the values to use.
TABLE 23. MFR_READ_IIN Register
Value
Meaning
Default
0h – 0FFFh
Measured value
for input current
sense voltage
0000h
MFR_SPECIFIC_02: MFR_READ_PIN (D2h)
The MFR_READ_PIN command will report the upper 12 bits
of the VIN x IIN product as measured by the 12-bit ADC. To
read data from the MFR_READ_PIN command, use the PM-
Bus Read Word protocol. Reading this register should use
the coefficients shown in the Telemetry and Warning Con-
version Coefficients Table. Please see the section on coeffi-
cient calculations to calculate the values to use.
TABLE 24. MFR_READ_PIN Register
Value
Meaning
Default
0h – 0FFFh
Value for input
current x input
voltage
0000h
MFR_SPECIFIC_03: MFR_IN_OC_WARN_LIMIT (D3h)
The MFR_IIN_OC_WARN_LIMIT PMBus command sets
the input over-current warning threshold. In the event that the
input current rises above the value set in this register, the IIN
Over-current flags are set in the status registers and the SM-
BA is asserted. To access the MFR_IIN_OC_WARN_LIMIT
register, use the PMBus Read/Write Word protocol. Read-
ing/writing to this register should use the coefficients shown
in the Telemetry and Warning Conversion Coefficients Table.
TABLE 25. MFR_IIN_OC_WARN_LIMIT Register
Value
Meaning
Default
0h – 0FFEh
Value for input
over-current warn
limit
0FFFh
Input over-current
warning disabled
n/a
MFR_SPECIFIC_04: MFR_PIN_OP_WARN_LIMIT (D4h)
The MFR_PIN_OP_WARN_LIMIT PMBus command sets
the input over-power warning threshold. In the event that the
input power rises above the value set in this register, the PIN
Over-power flags are set in the status registers and the SM-
BA is asserted. To access the MFR_PIN_OP_WARN_LIMIT
register, use the PMBus Read/Write Word protocol. Read-
ing/writing to this register should use the coefficients shown
in the Telemetry and Warning Conversion Coefficients Table.
TABLE 26. MFR_PIN_OP_WARN_LIMIT Register
Value
Meaning
Default
0h – 0FFEh
Value for input
over-power warn
limit
0FFFh
Input over-power
warning disabled
n/a
MFR_SPECIFIC_05: READ_PIN_PEAK (D5h)
The READ_PIN_PEAK command will report the maximum
input power measured since a Power On reset or the last
CLEAR_PIN_PEAK
command.
To
access
the
READ_PIN_PEAK command, use the PMBus Read Word
protocol. Use the coefficients shown in the Telemetry and
Warning Coefficients Table.
TABLE 27. READ_PIN_PEAK Register
Value
Meaning
Default
0h – 0FFEh
Maximum Value
for input current x
input voltage since
reset or last clear
0h
MFR_SPECIFIC_06: CLEAR_PIN_PEAK (D6h)
The CLEAR_PIN_PEAK command will clear the PIN_PEAK
register. This command uses the PMBus Send Byte proto-
col.
MFR_SPECIFIC_07: GATE_MASK (D7h)
The GATE_MASK register allows the hardware to prevent
fault conditions from switching off the MOSFET. When the bit
is high, the corresponding FAULT has no control over the
MOSFET gate. All status registers will still be updated (STA-
TUS, DIAGNOSTIC) and an SMBA will still be issued. This
register is accessed with the PMBus Read / Write Byte pro-
tocol.
Warning:
Inhibiting the MOSFET switch off in response to over-cur-
rent or circuit breaker fault conditions will likely result in
the destruction of the MOSFET! This functionality should
be used with great care and supervision!
www.national.com
34
LM25066A
相关PDF资料 |
PDF描述 |
|---|---|
| LM2575T-012G | 3.2 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, SFM5 |
| LM2577K-12/883 | 6 A SWITCHING REGULATOR, 62 kHz SWITCHING FREQ-MAX, MBFM2 |
| LM2577KADJ/883 | 6 A SWITCHING REGULATOR, 62 kHz SWITCHING FREQ-MAX, MBCY4 |
| LM2577K-15/883 | 6 A SWITCHING REGULATOR, 62 kHz SWITCHING FREQ-MAX, MBFM2 |
| LM2633MTDX/NOPB | SWITCHING CONTROLLER, 275 kHz SWITCHING FREQ-MAX, PDSO48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM25066APSQE/NOPB | 功能描述:热插拔功率分布 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| LM25066APSQX | 制造商:TI 制造商全称:Texas Instruments 功能描述:System Power Management and Protection IC with PMBusa?￠ |
| LM25066APSQX/NOPB | 功能描述:热插拔功率分布 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| LM25066EVK/NOPB | 功能描述:电源管理IC开发工具 LM25066 EVAL BOARD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| LM25066IAPSQ/NOPB | 制造商:Texas Instruments 功能描述:IC PWR MGMT/PROT PMBUS 24WQFN 制造商:Texas Instruments 功能描述:System PWR Mgmt & Protection IC |
发布紧急采购，3分钟左右您将得到回复。