- 您现在的位置：买卖IC网 > PDF目录44546 > LM2574-ADJMWC (NATIONAL SEMICONDUCTOR CORP) 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC PDF资料下载
参数资料
| 型号： | LM2574-ADJMWC |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC |
| 封装： | WAFER |
| 文件页数： | 4/33页 |
| 文件大小： | 814K |
| 代理商： | LM2574-ADJMWC |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
LM2574 Series Buck Regulator Design Procedure
PROCEDURE (Fixed Output Voltage Versions)
EXAMPLE (Fixed Output Voltage Versions)
Given:
V
OUT = Regulated Output Voltage (3.3V, 5V, 12V, or 15V)
V
IN(Max) = Maximum Input Voltage
I
LOAD(Max) = Maximum Load Current
Given:
V
OUT = 5V
V
IN(Max) = 15V
I
LOAD(Max) = 0.4A
1. Inductor Selection (L1)
A. Select the correct Inductor value selection guide from
Fig-
ures 4, 5, 6,or Figure 7. (Output voltages of 3.3V, 5V, 12V or
15V respectively). For other output voltages, see the design
procedure for the adjustable version.
B. From the inductor value selection guide, identify the induc-
tance region intersected by V
IN(Max) and ILOAD(Max).
C. Select an appropriate inductor from the table shown in
Fig-
ure 3. Part numbers are listed for three inductor manufactur-
ers. The inductor chosen must be rated for operation at the
LM2574 switching frequency (52 kHz) and for a current rating
of 1.5 x I
LOAD. For additional inductor information, see the in-
ductor section in the Application Hints section of this data
sheet.
1. Inductor Selection (L1)
A. Use the selection guide shown in
Figure 5.
B. From the selection guide, the inductance area intersected
by the 15V line and 0.4A line is 330.
C. Inductor value required is 330 H. From the table in
Figure
3, choose Pulse Engineering PE-52627, Renco RL-1284-330,
or NPI NP5920/5921.
2. Output Capacitor Selection (C
OUT)
A. The value of the output capacitor together with the inductor
defines the dominate pole-pair of the switching regulator loop.
For stable operation and an acceptable output ripple voltage,
(approximately 1% of the output voltage) a value between
100 F and 470 F is recommended.
B. The capacitor’s voltage rating should be at least 1.5 times
greater than the output voltage. For a 5V regulator, a rating of
at least 8V is appropriate, and a 10V or 15V rating is recom-
mended.
Higher voltage electrolytic capacitors generally have lower
ESR numbers, and for this reason it may be necessary to se-
lect a capacitor rated for a higher voltage than would normally
be needed.
2. Output Capacitor Selection (C
OUT)
A. C
OUT = 100 F to 470 F standard aluminum electrolytic.
B. Capacitor voltage rating = 20V.
3. Catch Diode Selection (D1)
A. The catch-diode current rating must be at least 1.5 times
greater than the maximum load current. Also, if the power
supply design must withstand a continuous output short, the
diode should have a current rating equal to the maximum cur-
rent limit of the LM2574. The most stressful condition for this
diode is an overload or shorted output condition.
B. The reverse voltage rating of the diode should be at least
1.25 times the maximum input voltage.
3. Catch Diode Selection (D1)
A. For this example, a 1A current rating is adequate.
B. Use a 20V 1N5817 or SR102 Schottky diode, or any of the
suggested fast-recovery diodes shown in
Figure 9.
4. Input Capacitor (C
IN)
An aluminum or tantalum electrolytic bypass capacitor located
close to the regulator is needed for stable operation.
4. Input Capacitor (C
IN)
A 22 F aluminum electrolytic capacitor located near the input
and ground pins provides sufficient bypassing.
www.national.com
12
相关PDF资料 |
PDF描述 |
|---|---|
| LM2574N-15/NOPB | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PDIP8 |
| LM2574M-15/NOPB | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PDSO14 |
| LM2574-ADJMDC | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC |
| LM2574-12MDC | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC |
| LM2574-5.0MDC | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM2574BN | 功能描述:IC REG BUCK ADJ 0.5A 8DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:20 系列:SIMPLE SWITCHER® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:12V 输入电压:4 V ~ 60 V PWM 型:电压模式 频率 - 开关:52kHz 电流 - 输出:1A 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:16-DIP（0.300"，7.62mm） 包装:管件 供应商设备封装:16-DIP 其它名称:*LM2575HVN-12LM2575HVN-12 |
| LM2574BWM | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:RF Micro Devices Inc 功能描述: 制造商:Micrel Inc 功能描述: |
| LM2574DW | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:0.5 A, Adjustable Output Voltage, Step-Down Switching Regulator |
| LM2574DW-ADJ | 功能描述:直流/直流开关调节器 500mA Adj. Step Down RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| LM2574DW-ADJR2 | 功能描述:直流/直流开关调节器 500mA Adj. Step Down RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。