- 您现在的位置：买卖IC网 > PDF目录80302 > LM2575-12MWC (NATIONAL SEMICONDUCTOR CORP) 3.2 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC PDF资料下载
参数资料
| 型号： | LM2575-12MWC |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 3.2 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC |
| 封装： | WAFER |
| 文件页数： | 3/40页 |
| 文件大小： | 917K |
| 代理商： | LM2575-12MWC |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
LM2575 Series Buck Regulator Design Procedure
PROCEDURE (Fixed Output Voltage Versions)
EXAMPLE (Fixed Output Voltage Versions)
Given:
V
OUT = Regulated Output Voltage (3.3V, 5V, 12V, or 15V)
V
IN(Max) = Maximum Input Voltage
I
LOAD(Max) = Maximum Load Current
Given:
V
OUT =5V
V
IN(Max) = 20V
I
LOAD(Max) = 0.8A
1. Inductor Selection (L1)
A. Select the correct Inductor value selection guide from
Figures 3, 4, 5, 6 (Output voltages of 3.3V, 5V, 12V or 15V
respectively). For other output voltages, see the design pro-
cedure for the adjustable version.
B. From the inductor value selection guide, identify the induc-
tance region intersected by V
IN(Max) and ILOAD(Max), and
note the inductor code for that region.
C. Identify the inductor value from the inductor code, and
select an appropriate inductor from the table shown in
9. Part numbers are listed for three inductor manufacturers.
The inductor chosen must be rated for operation at the
LM2575 switching frequency (52 kHz) and for a current rating
of 1.15 x I
LOAD. For additional inductor information, see the
inductor section in the Application Hints section of this data
sheet.
1. Inductor Selection (L1)
A. Use the selection guide shown in
B. From the selection guide, the inductance area intersected
by the 20V line and 0.8A line is L330.
C. Inductor value required is 330 H. From the table in
9, choose AIE 415-0926, Pulse Engineering PE-52627, or
RL1952.
2. Output Capacitor Selection (C
OUT)
A. The value of the output capacitor together with the inductor
defines the dominate pole-pair of the switching regulator loop.
For stable operation and an acceptable output ripple voltage,
(approximately 1% of the output voltage) a value between 100
F and 470 F is recommended.
B. The capacitor’s voltage rating should be at least 1.5 times
greater than the output voltage. For a 5V regulator, a rating of
at least 8V is appropriate, and a 10V or 15V rating is recom-
mended.
Higher voltage electrolytic capacitors generally have lower
ESR numbers, and for this reasion it may be necessary to
select a capacitor rated for a higher voltage than would nor-
mally be needed.
2. Output Capacitor Selection (C
OUT)
A. C
OUT = 100 F to 470 F standard aluminum electrolytic.
B. Capacitor voltage rating = 20V.
3. Catch Diode Selection (D1)
A. The catch-diode current rating must be at least 1.2 times
greater than the maximum load current. Also, if the power
supply design must withstand a continuous output short, the
diode should have a current rating equal to the maximum
current limit of the LM2575. The most stressful condition for
this diode is an overload or shorted output condition.
B. The reverse voltage rating of the diode should be at least
1.25 times the maximum input voltage.
3. Catch Diode Selection (D1)
A. For this example, a 1A current rating is adequate.
B. Use a 30V 1N5818 or SR103 Schottky diode, or any of the
suggested fast-recovery diodes shown in
4. Input Capacitor (C
IN)
An aluminum or tantalum electrolytic bypass capacitor located
close to the regulator is needed for stable operation.
4. Input Capacitor (C
IN)
A 47 F, 25V aluminum electrolytic capacitor located near the
input and ground pins provides sufficient bypassing.
LM1575/LM2575/LM2575HV
www.national.com
11
相关PDF资料 |
PDF描述 |
|---|---|
| LSN-1.2/15-D12H | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LES008ZDN18 | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| LES015YJN39 | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| LNK304GNTL | 0.4 A SWITCHING REGULATOR, 70 kHz SWITCHING FREQ-MAX, PDSO8 |
| LM3702XDBPX-308/NOPB | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PBGA9 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM2575-12T | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Easy Switcher 1.0 A Step-Down Voltage Regulator(389.50 k) |
| LM2575-12TA5R | 制造商:FCI 制造商全称:First Components International 功能描述:1.0A Step - Down Voltage Switching Regulators 1A output current |
| LM2575-12TA5T | 制造商:FCI 制造商全称:First Components International 功能描述:1.0A Step - Down Voltage Switching Regulators 1A output current |
| LM2575-12TB5BT | 制造商:FCI 制造商全称:First Components International 功能描述:1.0A Step - Down Voltage Switching Regulators 1A output current |
| LM2575-12TB5T | 制造商:FCI 制造商全称:First Components International 功能描述:1.0A Step - Down Voltage Switching Regulators 1A output current |
发布紧急采购，3分钟左右您将得到回复。