- 您现在的位置：买卖IC网 > PDF目录14434 > LM2575D2T-ADJR4G (ON Semiconductor)IC REG BUCK ADJ 1A D2PAK PDF资料下载
参数资料
| 型号： | LM2575D2T-ADJR4G |
| 厂商： | ON Semiconductor |
| 文件页数： | 8/28页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1A D2PAK |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.23 V ~ 37 V |
| 输入电压： | 4.75 V ~ 40 V |
| PWM 型： | 电压模式 |
| 频率 - 开关： | 52kHz |
| 电流 - 输出： | 1A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-263-6，D²Pak（5 引线+接片），TO-263BA |
| 包装： | 标准包装 |
| 供应商设备封装： | D2PAK-5 |
| 其它名称： | LM2575D2T-ADJR4GOSDKR |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LM2575, NCV2575
PIN FUNCTION DESCRIPTION
Pin
1
2
3
4
5
Symbol
V in
Output
GND
Feedback
ON/OFF
Description (Refer to Figure 1)
This pin is the positive input supply for the LM2575 step ? down switching regulator. In order to minimize
voltage transients and to supply the switching currents needed by the regulator, a suitable input bypass
capacitor must be present (C in in Figure 1).
This is the emitter of the internal switch. The saturation voltage V sat of this output switch is typically 1.0 V.
It should be kept in mind that the PCB area connected to this pin should be kept to a minimum in order to
minimize coupling to sensitive circuitry.
Circuit ground pin. See the information about the printed circuit board layout.
This pin senses regulated output voltage to complete the feedback loop. The signal is divided by the
internal resistor divider network R2, R1 and applied to the non ? inverting input of the internal error amplifier.
In the Adjustable version of the LM2575 switching regulator this pin is the direct input of the error amplifier
and the resistor network R2, R1 is connected externally to allow programming of the output voltage.
It allows the switching regulator circuit to be shut down using logic level signals, thus dropping the total
input supply current to approximately 80 m A. The input threshold voltage is typically 1.4 V. Applying a
voltage above this value (up to +V in ) shuts the regulator off. If the voltage applied to this pin is lower than
1.4 V or if this pin is connected to ground, the regulator will be in the “on” condition.
DESIGN PROCEDURE
Buck Converter Basics
The LM2575 is a “Buck” or Step ? Down Converter which
is the most elementary forward ? mode converter. Its basic
schematic can be seen in Figure 15.
current loop. This removes the stored energy from the
inductor.
The inductor current during this time is:
The operation of this regulator topology has two distinct
time periods. The first one occurs when the series switch is
on, the input voltage is connected to the input of the inductor.
I
L(off)
+
V
out
V
L
D
t
off
V out t on
in
L(on)
L
d + on , where T is the period of switching.
d + out
in
The output of the inductor is the output voltage, and the
rectifier (or catch diode) is reverse biased. During this
period, since there is a constant voltage source connected
across the inductor, the inductor current begins to linearly
ramp upwards, as described by the following equation:
V
I +
During this “on” period, energy is stored within the core
material in the form of magnetic flux. If the inductor is
properly designed, there is sufficient energy stored to carry
the requirements of the load during the “off” period.
This period ends when the power switch is once again
turned on. Regulation of the converter is accomplished by
varying the duty cycle of the power switch. It is possible to
describe the duty cycle as follows:
t
T
For the buck converter with ideal components, the duty
cycle can also be described as:
V
V
Figure 16 shows the buck converter idealized waveforms
of the catch diode voltage and the inductor current.
Power
Switch
L
V out
V in
D1
C out
R Load
Figure 15. Basic Buck Converter
The next period is the “off” period of the power switch.
When the power switch turns off, the voltage across the
inductor reverses its polarity and is clamped at one diode
voltage drop below ground by catch dioded. Current now
flows through the catch diode thus maintaining the load
http://onsemi.com
8
相关PDF资料 |
PDF描述 |
|---|---|
| V72B28E250BG3 | CONVERTER MOD DC/DC 28V 250W |
| MAX16073RS20D2+T | IC MPU SUPERVISOR CIRCUIT 4UCSP |
| RSC10DRYS-S734 | CONN EDGECARD 20POS DIP .100 SLD |
| V72B28E250BG | CONVERTER MOD DC/DC 28V 250W |
| LM2575D2T-5R4G | IC REG BUCK 5V 1A D2PAK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM2575EP | 制造商:NSC 制造商全称:National Semiconductor 功能描述:SIMPLE SWITCHER 1A Step-Down Voltage Regulator |
| LM2575HV | 制造商:NSC 制造商全称:National Semiconductor 功能描述:SIMPLE SWITCHER 1A Step-Down Voltage Regulator |
| LM2575HVM12 | 制造商:Texas Instruments 功能描述:* |
| LM2575HVM-12 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:SIMPLE SWITCHER 1A Step-Down Voltage Regulator |
| LM2575HVM-12/NOPB | 功能描述:IC REG BUCK 12V 1A 24-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:SIMPLE SWITCHER® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:3.3V 输入电压:4.5 V ~ 24 V PWM 型:- 频率 - 开关:- 电流 - 输出:125mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 包装:Digi-Reel® 供应商设备封装:SOT-6 其它名称:MAX1836EUT33#TG16DKR |
发布紧急采购，3分钟左右您将得到回复。