- 您现在的位置：买卖IC网 > PDF目录39246 > LM2576TV-12G (ON SEMICONDUCTOR) 7.5 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PZFM5 PDF资料下载
参数资料
| 型号： | LM2576TV-12G |
| 厂商： | ON SEMICONDUCTOR |
| 元件分类： | 稳压器 |
| 英文描述： | 7.5 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PZFM5 |
| 封装： | LEAD FREE, TO-220, 5 PIN |
| 文件页数： | 13/28页 |
| 文件大小： | 275K |
| 代理商： | LM2576TV-12G |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LM2576
http://onsemi.com
20
Figure 29. Inverting BuckBoost Regulator Shutdown
Circuit Using a PNP Transistor
NOTE: This picture does not show the complete circuit.
R2
5.6 k
Q1
2N3906
LM2576XX
1
3
5GN
D
ON/OFF
R1
12 k
Vout
+Vin
Shutdown
Input
Off
On
+V
0
+Vin
Cin
100
mF
Negative Boost Regulator
This example is a variation of the buckboost topology
and it is called negative boost regulator. This regulator
experiences relatively high switch current, especially at low
input voltages. The internal switch current limiting results in
lower output load current capability.
The circuit in Figure 30 shows the negative boost
configuration. The input voltage in this application ranges
from 5.0 V to 12 V and provides a regulated 12 V output.
If the input voltage is greater than 12 V, the output will rise
above 12 V accordingly, but will not damage the regulator.
Figure 30. Negative Boost Regulator
1N5820
100
mH
Output
2
4
Feedback
Vout = 12 V
Typical Load Current
400 mA for Vin = 5.2 V
750 mA for Vin = 7.0 V
5.0 V to 12 V
Cout
2200
mF
Low Esr
Cin
100
mF
LM257612
1
5
3
ON/OFF
GND
Vin
Design Recommendations:
The same design rules as for the previous inverting
buckboost converter can be applied. The output capacitor
Cout must be chosen larger than would be required for a what
standard buck converter. Low input voltages or high output
currents require a large value output capacitor (in the range
of thousands of
mF). The recommended range of inductor
values for the negative boost regulator is the same as for
inverting converter design.
Another important point is that these negative boost
converters cannot provide current limiting load protection in
the event of a short in the output so some other means, such
as a fuse, may be necessary to provide the load protection.
Delayed Startup
There are some applications, like the inverting regulator
already mentioned above, which require a higher amount of
startup current. In such cases, if the input power source is
limited, this delayed startup feature becomes very useful.
To provide a time delay between the time when the input
voltage is applied and the time when the output voltage
comes up, the circuit in Figure 31 can be used. As the input
voltage is applied, the capacitor C1 charges up, and the
voltage across the resistor R2 falls down. When the voltage
on the ON/OFF pin falls below the threshold value 1.3 V, the
regulator starts up. Resistor R1 is included to limit the
maximum voltage applied to the ON/OFF pin. It reduces the
power supply noise sensitivity, and also limits the capacitor
C1 discharge current, but its use is not mandatory.
When a high 50 Hz or 60 Hz (100 Hz or 120 Hz
respectively) ripple voltage exists, a long delay time can
cause some problems by coupling the ripple into the
ON/OFF pin, the regulator could be switched periodically
on and off with the line (or double) frequency.
Figure 31. Delayed Startup Circuitry
R1
47 k
LM2576XX
1
3
5GN
D
ON/OFF
R2
47 k
+Vin
C1
0.1
mF
Cin
100
mF
NOTE: This picture does not show the complete circuit.
Undervoltage Lockout
Some applications require the regulator to remain off until
the input voltage reaches a certain threshold level. Figure 32
shows an undervoltage lockout circuit applied to a buck
regulator. A version of this circuit for buckboost converter
is shown in Figure 33. Resistor R3 pulls the ON/OFF pin
high and keeps the regulator off until the input voltage
reaches a predetermined threshold level with respect to the
ground Pin 3, which is determined by the following
expression:
V
th [
V
Z1 )
1.0
) R2
R1
V
BE
(Q1)
相关PDF资料 |
PDF描述 |
|---|---|
| LM2596-12MWC | 7.5 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, UUC |
| LM2596-ADJMWC | 7.5 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, UUC |
| LM2596-ADJMDC | 7.5 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, UUC |
| LM2601MDC | 1-CHANNEL POWER SUPPLY SUPPORT CKT, UUC |
| LM2601MWC | 1-CHANNEL POWER SUPPLY SUPPORT CKT, UUC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM2576TV-15 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:3.0A, 15V, Step-Down Switching Regulator |
| LM2576TV-3.3 | 功能描述:直流/直流开关调节器 3.3V 3A Buck PWM RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| LM2576TV-3.3G | 功能描述:直流/直流开关调节器 3.3V 3A Buck PWM RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| LM2576TV-5 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:EASY SWITCHER 3.0 A STEP.DOWN VOLTAGE REGULATOR |
| LM2576TV-5.0 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:3.0A, 15V, Step-Down Switching Regulator |
发布紧急采购，3分钟左右您将得到回复。