- 您现在的位置：买卖IC网 > PDF目录44549 > LM2588-12MWC (NATIONAL SEMICONDUCTOR CORP) 9.5 A SWITCHING REGULATOR, 200 kHz SWITCHING FREQ-MAX, UUC PDF资料下载
参数资料
| 型号： | LM2588-12MWC |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 9.5 A SWITCHING REGULATOR, 200 kHz SWITCHING FREQ-MAX, UUC |
| 封装： | WAFER |
| 文件页数： | 16/33页 |
| 文件大小： | 863K |
| 代理商： | LM2588-12MWC |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
Application Hints
LM2588 SPECIAL FEATURES
SHUTDOWN CONTROL
A feature of the LM2588 is its ability to be shut down using
the ON /OFF pin (pin 1). This feature conserves input power
by turning off the device when it is not in use. For proper op-
eration, an isolation diode is required (as shown in
Figure
41).
The device will shut down when 3V or greater is applied on
the ON /OFF pin, sourcing current into pin 1. In shut down
mode, the device will draw typically 56 A of supply current
(16 A to V
IN and 40 A to the ON /OFF pin). To turn the de-
vice back on, leave pin 1 floating, using an (isolation) diode,
as shown in
Figure 41 (for normal operation, do not source
or sink current to or from this pin — see the next section).
FREQUENCY ADJUSTMENT
The switching frequency of the LM2588 can be adjusted with
the use of an external resistor. This feature allows the user to
optimize the size of the magnetics and the output capaci-
tor(s) by tailoring the operating frequency. A resistor con-
nected from pin 1 (the Freq. Adj. pin) to ground will set the
switching frequency from 100 kHz to 200 kHz (maximum).
As shown in
Figure 41, the pin can be used to adjust the fre-
quency while still providing the shut down function. A curve in
the Performance Characteristics Section graphs the resistor
value to the corresponding switching frequency. The table in
Figure 42 shows resistor values corresponding to commonly
used frequencies.
However, changing the LM2588’s operating frequency from
its nominal value of 100 kHz will change the magnetics se-
lection and compensation component values.
FREQUENCY SYNCHRONIZATION
Another feature of the LM2588 is the ability to synchronize
the switching frequency to an external source, using the
sync pin (pin 6). This feature allows the user to parallel mul-
tiple devices to deliver more output power.
A negative falling pulse applied to the sync pin will synchro-
nize the LM2588 to an external oscillator (see
Figure 43 and
44).
Use of this feature enables the LM2588 to be synchronized
to an external oscillator, such as a system clock. This opera-
tion allows multiple power supplies to operate at the same
frequency,
thus
eliminating
frequency-related
noise
problems.
The scope photo in
Figure 44 shows a LM2588 12V Boost
Regulator synchronized to a 200 kHz signal. There is a 700
ns delay between the falling edge of the sync signal and the
turning on of the switch.
PROGRAMMING OUTPUT VOLTAGE
(SELECTING R1 AND R2)
Referring to the adjustable regulator in
Figure 45, the output
voltage is programmed by the resistors R1 and R2 by the fol-
lowing formula:
V
OUT = VREF (1 + R1/R2)
where V
REF = 1.23V
Resistors R1 and R2 divide the output voltage down so that
it can be compared with the 1.23V internal reference. With
R2 between 1k and 5k, R1 is:
R1 = R2 (V
OUT/VREF 1)
where V
REF = 1.23V
For best temperature coefficient and stability with time, use
1% metal film resistors.
SHORT CIRCUIT CONDITION
Due to the inherent nature of boost regulators, when the out-
put is shorted (see
Figure 45 ), current flows directly from the
input, through the inductor and the diode, to the output, by-
passing the switch. The current limit of the switch
does not
limit the output current for the entire circuit. To protect the
DS012420-54
FIGURE 41. Shutdown Operation
R
SET(k)
Frequency (kHz)
Open
100
200
125
47
150
33
175
22
200
FIGURE 42. Frequency Setting Resistor Guide
DS012420-55
FIGURE 43. Frequency Synchronization
DS012420-64
FIGURE 44. Waveforms of a Synchronized
12V Boost Regulator
www.national.com
23
相关PDF资料 |
PDF描述 |
|---|---|
| LM2588-12MDC | 9.5 A SWITCHING REGULATOR, 200 kHz SWITCHING FREQ-MAX, UUC |
| LM2588-ADJMWC | 9.5 A SWITCHING REGULATOR, 200 kHz SWITCHING FREQ-MAX, UUC |
| LM2588T-12/NOPB | 9.5 A SWITCHING REGULATOR, 200 kHz SWITCHING FREQ-MAX, PSFM7 |
| LM2590HV3.3MDC | 3 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, UUC |
| LM2594-12MDC | 1.4 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, UUC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM2588S-12 | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| LM2588S-12/NOPB | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| LM2588S-3.3 | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| LM2588S-3.3/NOPB | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| LM2588S-5.0 | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。