- 您现在的位置：买卖IC网 > PDF目录80151 > LM2599-5.0MDC (NATIONAL SEMICONDUCTOR CORP) 7.5 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, UUC PDF资料下载
参数资料
| 型号： | LM2599-5.0MDC |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 7.5 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, UUC |
| 封装： | DIE |
| 文件页数： | 10/36页 |
| 文件大小： | 897K |
| 代理商： | LM2599-5.0MDC |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
Block Diagram
Application Information
PIN FUNCTIONS
+V
IN (Pin 1) — This is the positive input supply for the IC
switching regulator. A suitable input bypass capacitor must
be present at this pin to minimize voltage transients and to
supply the switching currents needed by the regulator.
Ground (Pin 4) — Circuit ground.
Output (Pin 2) — Internal switch. The voltage at this pin
switches between approximately (+V
IN VSAT) and approxi-
mately 0.5V, with a duty cycle of V
OUT/VIN. To minimize
coupling to sensitive circuitry, the PC board copper area
connected to this pin should be kept to a minimum.
Feedback (Pin 6) — Senses the regulated output voltage to
complete the feedback loop.
Shutdown /Soft-start (Pin 7) — This dual function pin pro-
vides the following features: (a) Allows the switching regula-
tor circuit to be shut down using logic level signals thus
dropping the total input supply current to approximately
80 A. (b) Adding a capacitor to this pin provides a soft-start
feature which minimizes startup current and provides a con-
trolled ramp up of the output voltage.
Error Flag (Pin 3) — Open collector output that provides a
low signal (flag transistor ON) when the regulated output
voltage drops more than 5% from the nominal output volt-
age. On start up, Error Flag is low until V
OUT reaches 95% of
the nominal output voltage and a delay time determined by
the Delay pin capacitor. This signal can be used as a reset to
a microprocessor on power-up.
Delay (Pin 5) — At power-up, this pin can be used to provide
a time delay between the time the regulated output voltage
reaches 95% of the nominal output voltage, and the time the
error flag output goes high.
Special Note If any of the above three features (Shutdown
/Soft-start, Error Flag, or Delay) are not used, the respective
pins should be left open.
EXTERNAL COMPONENTS
SOFT-START CAPACITOR
C
SS — A capacitor on this pin provides the regulator with a
Soft-start feature (slow start-up). When the DC input voltage
is first applied to the regulator, or when the Shutdown
/Soft-start pin is allowed to go high, a constant current
(approximately 5 A begins charging this capacitor). As the
capacitor voltage rises, the regulator goes through four op-
erating regions (See the bottom curve in
Figure 13).
1. Regulator in Shutdown. When the SD /SS pin voltage is
between 0V and 1.3V, the regulator is in shutdown, the
output voltage is zero, and the IC quiescent current is ap-
proximately 85 A.
2. Regulator ON, but the output voltage is zero. With the
SD /SS pin voltage between approximately 1.3V and 1.8V,
the internal regulator circuitry is operating, the quiescent
current rises to approximately 5 mA, but the output voltage is
still zero. Also, as the 1.3V threshold is exceeded, the
Soft-start capacitor charging current decreases from 5 A
down to approximately 1.6 A. This decreases the slope of
capacitor voltage ramp.
3. Soft-start Region. When the SD /SS pin voltage is be-
tween 1.8V and 2.8V (@ 25C), the regulator is in a Soft-start
condition. The switch (Pin 2) duty cycle initially starts out
very low, with narrow pulses and gradually get wider as the
capacitor SD /SS pin ramps up towards 2.8V. As the duty
cycle increases, the output voltage also increases at a con-
trolled ramp up. See the center curve in
Figure 13. The input
supply current requirement also starts out at a low level for
DS012582-30
FIGURE 12.
LM2599
www.national.com
18
相关PDF资料 |
PDF描述 |
|---|---|
| LSN-1.5/10-D12B | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LTC3521EUF#PBF | SWITCHING REGULATOR, 1350 kHz SWITCHING FREQ-MAX, PQCC24 |
| LM1576-15AK | 3.5 A SWITCHING REGULATOR, 52 kHz SWITCHING FREQ-MAX, MBFM2 |
| LM1575HVK-ADJ/883 | 1.3 A SWITCHING REGULATOR, 52 kHz SWITCHING FREQ-MAX, MBFM2 |
| LX2174IM | 2.8 A SWITCHING REGULATOR, 115 kHz SWITCHING FREQ-MAX, PDIP8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM2599S-12 | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| LM2599S-12/NOPB | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| LM2599S-3.3 | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| LM2599S-3.3/NOPB | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| LM2599S-5.0 | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。