- 您现在的位置：买卖IC网 > PDF目录17247 > LM2621EVAL (National Semiconductor)EVALUATION BOARD FOR LM2621 PDF资料下载
参数资料
| 型号： | LM2621EVAL |
| 厂商： | National Semiconductor |
| 文件页数： | 8/17页 |
| 文件大小： | 0K |
| 描述： | EVALUATION BOARD FOR LM2621 |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步升 |
| 输出及类型： | 1，非隔离 |
| 输入电压： | 1.2 ~ 14 V |
| 稳压器拓扑结构： | 升压 |
| 板类型： | 完全填充 |
| 已供物品： | 板，文档 |
| 已用 IC / 零件： | LM2621 |
| 相关产品： | LM2621MMDKR-ND - IC REG BST FLYBK SEPIC ADJ 8MSOP LM2621MMX/NOPBTR-ND - IC REG BST FLYBK SEPIC ADJ 8MSOP LM2621MMTR-ND - IC REG BST FLYBK SEPIC ADJ 8MSOP LM2621MMCT-ND - IC REG BST FLYBK SEPIC ADJ 8MSOP |
| 其它名称： | *LM2621EVAL |
SNVS033C – MAY 2004 – REVISED MARCH 2005
Design Procedure
SETTING THE OUTPUT VOLTAGE
The output voltage of the step-up regulator can be set between 1.24V and 14V by connecting a feedback
resistive divider made of R F1 and R F2 . The resistor values are selected as follows:
R F2 = R F1 /[(V OUT / 1.24) ? 1]
(1)
A value of 150k Ω is suggested for R F1 . Then, R F2 can be selected using the above equation. A 39pF capacitor
(C F1 ) connected across R F1 helps in feeding back most of the AC ripple at V OUT to the FB pin. This helps reduce
the peak-to-peak output voltage ripple as well as improve the efficiency of the step-up regulator, because a set
hysteresis of 30mV at the FB pin is used for the gated oscillator control scheme.
BOOTSTRAPPING
When the output voltage (V OUT ) is between 2.5V and 5.0V a bootstrapped operation is suggested. This is
achieved by connecting the V DD pin (Pin 6) to V OUT . However if the V OUT is outside this range, the V DD pin should
be connected to a voltage source whose range is between 2.5V and 5V. This can be the input voltage (V IN ), V OUT
stepped down using a linear regulator, or a different voltage source available in the system. This is referred to as
non-bootstrapped operation. The maximum acceptable voltage at the BOOT pin (Pin 7) is 10V.
SETTING THE SWITCHING FREQUENCY
The switching frequency of the oscillator is selected by choosing an external resistor (R FQ ) connected between
FREQ and V DD pins. See the graph titled " Switching Frequency vs RFQ ” in the TYPICAL PERFORMANCE
CHARACTERISTICS section of the datasheet for choosing the R FQ value to achieve the desired switching
frequency. A high switching frequency allows the use of very small surface mount inductors and capacitors and
results in a very small solution size. A switching frequency between 300kHz and 2MHz is recommended.
INDUCTOR SELECTION
The LM2621's high switching frequency enables the use of a small surface mount inductor. A 6.8μH shielded
inductor is suggested. The inductor should have a saturation current rating higher than the peak current it will
experience during circuit operation (see graph titled " Peak Inductor Current vs. Load Current ” in the TYPICAL
PERFORMANCE CHARACTERISTICS section). Less than 100m Ω ESR is suggested for high efficiency.
Open-core inductors cause flux linkage with circuit components and interfere with the normal operation of the
circuit. They should be avoided. For high efficiency, choose an inductor with a high frequency core material, such
as ferrite, to reduce the core losses. To minimize radiated noise, use a toroid, pot core or shielded core inductor.
The inductor should be connected to the SW pin as close to the IC as possible. See Table 1 for a list of the
inductor manufacturers.
OUTPUT DIODE SELECTION
A Schottky diode should be used for the output diode. The forward current rating of the diode should be higher
than the load current, and the reverse voltage rating must be higher than the output voltage. Do not use ordinary
rectifier diodes, since slow switching speeds and long recovery times cause the efficiency and the load regulation
to suffer. Table 1 shows a list of the diode manufacturers.
INPUT AND OUTPUT FILTER CAPACITORS SELECTION
Tantalum chip capacitors are recommended for the input and output filter capacitors. A 22μF capacitor is
suggested for the input filter capacitor. It should have a DC working voltage rating higher than the maximum
input voltage. A 68μF tantalum capacitor is suggested for the output capacitor. The DC working voltage rating
should be greater than the output voltage. Very high ESR values (>3 Ω ) should be avoided. Table 1 shows a list
of the capacitor manufacturers.
8
Product Folder Links: LM2621
Copyright ? 2004–2005, Texas Instruments Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| R1DA-3.31212-R | CONV DC/DC 1W 3.3V IN 12/12V OUT |
| RBC06DCST-S288 | CONN EDGECARD 12POS .100 EXTEND |
| R-78AA2.5-1.0SMD-R | CONV DC/DC 1A 4.75-18VIN 2.5V |
| R-78AA1.8-1.0SMD-R | CONV DC/DC 1A 4.75-18VIN 1.8V |
| R-78AA1.5-1.0SMD-R | CONV DC/DC 1A 4.75-18VIN 1.5V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM2621EVAL/NOPB | 功能描述:电源管理IC开发工具 EVAL BOARDFOR LM2621 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| LM2621MM | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| LM2621MM | 制造商:Texas Instruments 功能描述:DC/DC UP CONVERTER ADJ SMD 2621 |
| LM2621MM/NOPB | 功能描述:DC/DC 开关控制器 LOW INP VLTG,STEP-UP DC-DC RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| LM2621MM/NOPB | 制造商:Texas Instruments 功能描述:DC/DC Converter (DC-DC) / Switching Regu |
发布紧急采购，3分钟左右您将得到回复。