- 您现在的位置：买卖IC网 > PDF目录17413 > LM2735YMYEVAL (National Semiconductor)BOARD EVAL LM2735 520KHZ 8MSOP PDF资料下载
参数资料
| 型号： | LM2735YMYEVAL |
| 厂商： | National Semiconductor |
| 文件页数： | 12/58页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL LM2735 520KHZ 8MSOP |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步升 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 12V |
| 电流 - 输出： | 500mA |
| 输入电压： | 3 ~ 5.5 V |
| 稳压器拓扑结构： | 升压 |
| 频率 - 开关： | 520kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | LM2735 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页
SNVS485F – JUNE 2007 – REVISED APRIL 2013
V OUT x D
? V OUT = ? I L x R ESR + ¨ ¨
?
Because of the operating frequency of the LM2735, ferrite based inductors are preferred to minimize core losses.
This presents little restriction since the variety of ferrite-based inductors is huge. Lastly, inductors with lower
series resistance (DCR) will provide better operating efficiency. For recommended inductors see Example
Circuits.
INPUT CAPACITOR
An input capacitor is necessary to ensure that V IN does not drop excessively during switching transients. The
primary specifications of the input capacitor are capacitance, voltage, RMS current rating, and ESL (Equivalent
Series Inductance). The recommended input capacitance is 10 μF to 44 μF depending on the application. The
capacitor manufacturer specifically states the input voltage rating. Make sure to check any recommended
deratings and also verify if there is any significant change in capacitance at the operating input voltage and the
operating temperature. The ESL of an input capacitor is usually determined by the effective cross sectional area
of the current path. At the operating frequencies of the LM2735, certain capacitors may have an ESL so large
that the resulting impedance (2 π fL) will be higher than that required to provide stable operation. As a result,
surface mount capacitors are strongly recommended. Multilayer ceramic capacitors (MLCC) are good choices for
both input and output capacitors and have very low ESL. For MLCCs it is recommended to use X7R or X5R
dielectrics. Consult capacitor manufacturer datasheet to see how rated capacitance varies over operating
conditions.
OUTPUT CAPACITOR
The LM2735 operates at frequencies allowing the use of ceramic output capacitors without compromising
transient response. Ceramic capacitors allow higher inductor ripple without significantly increasing output ripple.
The output capacitor is selected based upon the desired output ripple and transient response. The initial current
of a load transient is provided mainly by the output capacitor. The output impedance will therefore determine the
maximum voltage perturbation. The output ripple of the converter is a function of the capacitor’s reactance and
its equivalent series resistance (ESR):
§ ·
?
? 2 x F SW x R Load x C OUT 1
(8)
When using MLCCs, the ESR is typically so low that the capacitive ripple may dominate. When this occurs, the
output ripple will be approximately sinusoidal and 90° phase shifted from the switching action .
Given the availability and quality of MLCCs and the expected output voltage of designs using the LM2735, there
is really no need to review any other capacitor technologies. Another benefit of ceramic capacitors is their ability
to bypass high frequency noise. A certain amount of switching edge noise will couple through parasitic
capacitances in the inductor to the output. A ceramic capacitor will bypass this noise while a tantalum will not.
Since the output capacitor is one of the two external components that control the stability of the regulator control
loop, most applications will require a minimum at 4.7 μF of output capacitance. Like the input capacitor,
recommended multilayer ceramic capacitors are X7R or X5R. Again, verify actual capacitance at the desired
operating voltage and temperature.
SETTING THE OUTPUT VOLTAGE
The output voltage is set using the following equation where R1 is connected between the FB pin and GND, and
R2 is connected between V OUT and the FB pin.
12
Product Folder Links: LM2735
Copyright ? 2007–2013, Texas Instruments Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| A9AAT-1803F | FLEX CABLE - AFE18T/AF18/AFE18T |
| LM2735YMFEVAL | BOARD EVAL LM2735 520KHZ 6LLP |
| SP7652EB | EVAL BOARD FOR SP7652 |
| A9BAA-1002E | FLEX CABLE - AFJ10A/AE10/AFH10T |
| 1SMA5923BT3G | DIODE ZENER 8.2V 1.5W SMA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM2735YMYEVAL | 制造商:Texas Instruments 功能描述:EVAL BOARD, LM2735Y 12V, 500mA SEPIC CON |
| LM2735YMYX | 制造商:NSC 制造商全称:National Semiconductor 功能描述:520kHz/1.6MHz - Space-Efficient Boost and SEPIC DC-DC Regulator |
| LM2735YMYX/NOPB | 功能描述:直流/直流开关调节器 RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| LM2735YQMF | 制造商:Texas Instruments 功能描述:IC, DC DC BOOST REG, 5SOT23 制造商:Texas Instruments 功能描述:IC, DC DC BOOST REG, 5SOT23; Primary Input Voltage:5.5V; No. of Outputs:1; Output Voltage:24V; Output Current:3A; Voltage Regulator Case Style:SOT-23; No. of Pins:5; Operating Temperature Min:-40C; Operating Temperature Max:125C; ;RoHS Compliant: Yes |
| LM2735YQMF/NOPB | 功能描述:直流/直流开关调节器 RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。