参数资料
型号: LM2735YSDEVAL
厂商: National Semiconductor
文件页数: 15/58页
文件大小: 0K
描述: BOARD EVAL LM2735 520KHZ 6LLP
标准包装: 1
主要目的: DC/DC,步升
输出及类型: 1,非隔离
输出电压: 12V
电流 - 输出: 500mA
输入电压: 3 ~ 5.5 V
稳压器拓扑结构: 升压
频率 - 开关: 520kHz
板类型: 完全填充
已供物品:
已用 IC / 零件: LM2735
V FB
R 2
V O
C 3
R LOAD
SNVS485F – JUNE 2007 – REVISED APRIL 2013
R 1
Figure 25. Setting External Pole-Zero
F ZERO - CF =
1
2 S ( R 2 x C 3 )
(14)
There is an associated pole with the zero that was created in the above equation.
F POLE - CF =
1
2 S ((R 1 R 2 ) x C 3 )
(15)
It is always higher in frequency than the zero.
A right-half plane zero (RHPZ) is inherent to all boost converters. One must remember that the gain associated
with a right-half plane zero increases at 20dB per decade, but the phase decreases by 45° per decade. For most
applications there is little concern with the RHPZ due to the fact that the frequency at which it shows up is well
beyond crossover, and has little to no effect on loop stability. One must be concerned with this condition for large
inductor values and high output currents.
( D ' ) R Load
RHP ZERO =
2
2 S x L
(16)
There are miscellaneous poles and zeros associated with parasitics internal to the LM2735, external
components, and the PCB. They are located well over the crossover frequency, and for simplicity are not
discussed.
PCB Layout Considerations
When planning layout there are a few things to consider when trying to achieve a clean, regulated output. The
most important consideration when completing a Boost Converter layout is the close coupling of the GND
connections of the C OUT capacitor and the LM2735 PGND pin. The GND ends should be close to one another
and be connected to the GND plane with at least two through-holes. There should be a continuous ground plane
on the bottom layer of a two-layer board except under the switching node island. The FB pin is a high impedance
node and care should be taken to make the FB trace short to avoid noise pickup and inaccurate regulation. The
feedback resistors should be placed as close as possible to the IC, with the AGND of R1 placed as close as
possible to the GND (pin 5 for the WSON) of the IC. The V OUT trace to R2 should be routed away from the
inductor and any other traces that are switching. High AC currents flow through the V IN , SW and V OUT traces, so
they should be as short and wide as possible. However, making the traces wide increases radiated noise, so the
designer must make this trade-off. Radiated noise can be decreased by choosing a shielded inductor. The
remaining components should also be placed as close as possible to the IC. Please see Application Note AN-
1229 SNVA054 for further considerations and the LM2735 demo board as an example of a four-layer layout.
Copyright ? 2007–2013, Texas Instruments Incorporated
Product Folder Links: LM2735
15
相关PDF资料
PDF描述
A9AAT-1606F FLEX CABLE - AFE16T/AF16/AFE16T
A9BAA-0905F FLEX CABLE - AFF09A/AF09/AFE09T
LM2735YMYEVAL BOARD EVAL LM2735 520KHZ 8MSOP
A9AAT-1803F FLEX CABLE - AFE18T/AF18/AFE18T
LM2735YMFEVAL BOARD EVAL LM2735 520KHZ 6LLP
相关代理商/技术参数
参数描述
LM2735YSDEVAL 制造商:Texas Instruments 功能描述:EVAL BOARD, LM2735Y 12V, 500mA SEPIC CON
LM2735YSDX 制造商:NSC 制造商全称:National Semiconductor 功能描述:520kHz/1.6MHz - Space-Efficient Boost and SEPIC DC-DC Regulator
LM2735YSDX/NOPB 功能描述:直流/直流开关调节器 RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5
LM2736 制造商:NSC 制造商全称:National Semiconductor 功能描述:Thin SOT23 750mA Load Step-Down DC-DC Regulator
LM2736X 制造商:TI 制造商全称:Texas Instruments 功能描述:LM2736 Thin SOT 750mA Load Step-Down DC-DC Regulator