- 您现在的位置：买卖IC网 > PDF目录17154 > LM2794EVAL (National Semiconductor)BOARD EVALUATION LM2794 PDF资料下载
参数资料
| 型号： | LM2794EVAL |
| 厂商： | National Semiconductor |
| 文件页数： | 12/23页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION LM2794 |
| 标准包装： | 1 |
| 电流 - 输出 / 通道： | 80mA |
| 输出及类型： | 4，非隔离 |
| 输出电压： | 4V |
| 特点： | 充电泵 |
| 输入电压： | 2.7 ~ 5.5 V |
| 已供物品： | 板 |
| 已用 IC / 零件： | LM2794 |
| 相关产品： | LM2794TLX/NOPB-ND - IC LED DRVR WHT BCKLT 14USMD LM2794BLDKR-ND - IC LED DRVR WHT BCKLT 14USMD LM2794TL/NOPBCT-ND - IC LED DRVR WHT BCKLT 14MICROSMD LM2794TL/NOPBTR-ND - IC LED DRVR WHT BCKLT 14MICROSMD LM2794BLCT-ND - IC LED DRVR WHT BCKLT 14USMD LM2794BLTR-ND - IC LED DRVR WHT BCKLT 14USMD |
SNVS168L – JANUARY 2002 – REVISED MAY 2013
2. Determine the maximum desired I LED current. Use the I LED equation to calculate R SET by setting BRGT to 0V
or use Table 3 to select a value for R SET when BRGT equals 0V.
3. Brightness control can be implemented by pulsing a signal at the SD pin. LED brightness is proportional to
the duty cycle (D) of the PWM signal. For linear brightness control over the full duty cycle adjustment range,
the PWM frequency (f) should be limited to accommodate the turn-on time (T ON = 100μs) of the device.
D × (1/f) > T ON
f MAX = D MIN ÷ T ON
If the PWM frequency is much less than 100Hz, flicker may be seen in the LEDs. For the LM2794, zero duty
cycle will turn off the LEDs and a 50% duty cycle will result in an average I LED being half of the programmed
LED current. For example, if R SET is set to program 15mA, a 50% duty cycle will result in an average I LED of
7.5mA. For the LM2795 however, 100% duty cycle will turn off the LEDs and a 50% duty cycle will result in
an average I LED being half the programmed LED current.
Brightness Control Using BRGT
1. Choose the maximum I LED desired and determine the max voltage to be applied to the BRGT pin. For
constant brightness, set BRGT to a fixed voltage between 0V to 3V.
2. Use Table 3 to determine the value of R SET required or use the I LED equation above to calculate R SET .
3. Use Table 4 as a reference for the dimming profile of the LEDs, when BRGT ranges from 0V to 3V.
Table 3. R SET Values
LED Current
BRGT
0.0V
0.5V
1.0V
1.5V
2.0V
2.5V
3.0V
5mA
374 ?
768 ?
1.15K ?
1.54K ?
1.91K ?
2.32K ?
2.67K ?
10mA
187 ?
383 ?
576 ?
768 ?
953 ?
1.15K ?
1.33K ?
15mA
124 ?
255 ?
383 ?
511 ?
624 ?
768 ?
909 ?
20mA
93.1 ?
191 ?
287 ?
383 ?
475 ?
576 ?
665 ?
Table 4. LED Current
R SET Values
BRGT
0.0V
0.5V
1.0V
1.5V
2.0V
2.5V
3.0V
2.67K ?
0.7mA
1.4mA
2.1mA
2.9mA
3.6mA
4.3mA
5.0mA
1.33K ?
1.4mA
2.9mA
4.3mA
5.8mA
7.2mA
8.7mA
10.1mA
909 ?
2.1mA
4.2mA
6.3mA
8.4mA
10.5mA
12.7mA
14.8mA
665 ?
2.8mA
5.7mA
8.6mA
11.5mA
14.4mA
17.3mA
20.2mA
CHARGE PUMP OUTPUT (P OUT )
The LM2794/5 charge pump is an unregulated switched capacitor converter with a gain of 1.5. The voltage at the
output of the pump (the P OUT pin) is nominally 1.5 × V IN . This rail can be used to deliver additional current to
other circuitry. Figure 23 shows how to connect additional LEDs to P OUT . A ballast resistor sets the current
through each LED, and LED current matching is dependent on the LED forward voltage matching. Because of
this, LEDs driven by P OUT are recommended for functions where brightness matching is not critical, such as
keypad backlighting.
Since P OUT is unregulated, driving LEDs directly off P OUT is usually practical only with a fixed input voltage. If the
input voltage is not fixed (Li-Ion battery, for example), using a linear regulator between the P OUT pin and the
LEDs is recommended. Texas Instruments LP3985-4.5V low-dropout linear regulator is a good choice for such
an application.
12
Product Folder Links: LM2794 LM2795
Copyright ? 2002–2013, Texas Instruments Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| QB-MINI2-K0R/LH3 | KIT DEMO 78K0R LH3 UPD78F1508 |
| 22R155MC | IND 1.5MH 0.16A DRUM 7.8X7.5 SMD |
| EBA10DTBH | CONN EDGECARD 20POS R/A .125 SLD |
| V300C36C75BG3 | CONVERTER MOD DC/DC 36V 75W |
| LBC2518T2R2M | INDUCTOR WOUND 2.2UH 630MA 1007 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM2794TL | 功能描述:IC LED DRVR WHT BCKLT 14MICROSMD RoHS:否 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
| LM2794TL/NOPB | 功能描述:LED照明驱动器 RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| LM2794TLX | 功能描述:IC LED DRVR WHT BCKLT 14USMD RoHS:否 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
| LM2794TLX/NOPB | 功能描述:LED照明驱动器 RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| LM2795 | 制造商:未知厂家 制造商全称:未知厂家 功能描述: |
发布紧急采购，3分钟左右您将得到回复。