- 您现在的位置：买卖IC网 > PDF目录20799 > LM2794TL (National Semiconductor)IC LED DRVR WHT BCKLT 14MICROSMD PDF资料下载
参数资料
| 型号： | LM2794TL |
| 厂商： | National Semiconductor |
| 文件页数： | 14/23页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR WHT BCKLT 14MICROSMD |
| 标准包装： | 1 |
| 恒定电流： | 是 |
| 拓扑： | PWM，切换式电容器（充电泵） |
| 输出数： | 4 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 325kHz ~ 675kHz |
| 电源电压： | 2.7 V ~ 5.5 V |
| 输出电压： | 3.8V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-WFBGA |
| 供应商设备封装： | 14-TuSMD |
| 包装： | 剪切带 (CT) |
| 工作温度： | -30°C ~ 85°C |
| 其它名称： | *LM2794TL LM2794TLCT |
SNVS168L – JANUARY 2002 – REVISED MAY 2013
18
16
14
12
10
8
6
4
2
0
R SET = 124Ω
R SET = 475Ω
R SET = 2.67kΩ
0.05
0.20
0.35
0.50
0.65
0.80
V HR (V)
Figure 24. I LED vs V HR
4 LEDs, V IN = 3.0V
On the flat part of the graph, the currents regulate properly as there is sufficient headroom voltage for regulation.
On the sloping part of the graph the headroom voltage is too small, the current sources are squeezed, and their
current drive capability is limited. Changes in headroom voltage from one output to the next, possible with LED
forward voltage mismatch, will result in different output currents and LED brightness mismatch. Thus, operating
the LM2794/5 with insufficient headroom voltage across the current sources should be avoided.
OUTPUT CURRENT CAPABILITY
The primary constraint on the total current capability is the headroom voltage requirement of the internal current
sources. Combining the V POUT and V HR equations from the previous two sections yields the basic inequality for
determining the validity of an LM2794/5 LED-drive application:
V POUT = 1.5 × V IN ? I TOTAL × R OUT
V HR-MIN = k HR × I DX
V POUT ? V DX ≥ V HR-MIN
1.5 × V IN ? I TOTAL × R OUT ? V DX ≥ (k HR × I DX )
Rearranging this inequality shows the estimated total output current capability of an application:
I TOTAL ≤ [(1.5 × V IN-MIN ) ? V DX-MAX ? (k HR × I DX )] ÷ R OUT
(4)
(5)
(6)
(7)
(8)
Examining the equation above, the primary limiting factors on total output current capability are input and LED
forward voltage. A low input voltage combined with a high LED voltage may result in insufficient headroom
voltage across the current sources, causing them to fall out of regulation. When the current sources are not
regulated, LED currents will be below desired levels and brightness matching will be highly dependent on LED
forward voltage matching.
Typical LM2794/5 output resistance is 3.0 ? . For worst-case design calculations, using an output resistance of
3.5 ? is recommended. LM2794/5 has a typical k HR constant of 20mV/mA. For worst-case design calculations,
use k HR = 25mV/mA. (Worst-case recommendations account for parameter shifts from part-to-part variation and
apply over the full operating temperature range). R OUT and k HR increase slightly with temperature, but losses are
typically offset by the negative temperature coefficient properties of LED forward voltages. Power dissipation and
internal self-heating may also limit output current capability but is discussed in a later section.
PARALLEL Dx OUTPUTS FOR INCREASED CURRENT DRIVE
Outputs D 1 through D 4 may be connected together in any combination to drive higher currents through fewer
LEDs. For example in Figure 25 , outputs D 1 and D 2 are connected together to drive one LED while D 3 and D 4
are connected together to drive a second LED.
14
Product Folder Links: LM2794 LM2795
Copyright ? 2002–2013, Texas Instruments Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| REC3-2412SRW/H2/A/M/SMD/CTRL | CONV DC/DC 3W 18-36VIN 12VOUT |
| P51-300-S-D-MD-5V-000-000 | SENSOR 300PSIS 7/16 UNF 5V MINI |
| USS 2-T220 2200.00 OHM 0.1% 3PPM | RES 2200 OHM 6W .1% FOIL SMD |
| P51-50-S-H-D-4.5OVP-000-000 | SENSOR 50PSI M12-1.5 6G .5-4.5V |
| REC7.5-1212DRW/H3/A/M/CTRL | CONV DC/DC 7.5W 9-18VIN +/-12V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM2794TL/NOPB | 功能描述:LED照明驱动器 RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| LM2794TLX | 功能描述:IC LED DRVR WHT BCKLT 14USMD RoHS:否 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
| LM2794TLX/NOPB | 功能描述:LED照明驱动器 RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| LM2795 | 制造商:未知厂家 制造商全称:未知厂家 功能描述: |
| LM27951 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:White LED Adaptive 1.5X/1X Switched Capacitor Current Driver |
发布紧急采购，3分钟左右您将得到回复。