- 您现在的位置：买卖IC网 > PDF目录22244 > LM334Z#TR (Linear Technology)IC CURRENT SOURCE TO92-3 PDF资料下载
参数资料
| 型号： | LM334Z#TR |
| 厂商： | Linear Technology |
| 文件页数： | 6/12页 |
| 文件大小： | 160K |
| 描述： | IC CURRENT SOURCE TO92-3 |
| 标准包装： | 2,000 |
| 功能： | 电流源 |
| 输入电压： | 0.8 V ~ 40 V |
| 电流 - 输出： | 10mA |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | TO-226-3、TO-92-3（TO-226AA）成形引线 |
| 供应商设备封装： | TO-92-3 |
| 包装： | 带卷 (TR) |
LM134 Series
6
Lead Resistance
The sense voltage which determines the operating current
of the LM134 is less than 100mV. At this level, thermo-
couple or lead resistance effects should be minimized by
locating the current setting resistor physically close to the
device. Sockets should be avoided if possible. It takes only
0.7& contact resistance to reduce output current by 1% at
the 1mA level.
Start-Up Time
The LM134 is designed to operate at currents as low as
1礎. This requires that internal biasing current be well
below that level because the device achieves its wide
operating current range by using part of the operating
current as bias current for the internal circuitry. To ensure
start-up, however, a fixed trickle current must be provided
internally. This is typically in the range of 20nA to 200nA
and is provided by the special ultralow I
DDS
FETs shown in
the Schematic Diagrams as Q7 and Q8. The start-up time
of the LM134 is determined by the I
DSS
of these FETs and
the capacitor C1. This capacitor must charge to approxi-
mately 500mV before Q3 turns on to start normal circuit
operation. This takes as long as (500mV)(50pF)/(20nA) =
1.25ms for very low I
DSS
values.
Using the LM134 as a Temperature Sensor
Because it has a highly linear output characteristic, the
LM134 makes a good temperature sensor. It is particularly
useful in remote sensing applications because it is a
current output device and is therefore not affected by long
wire runs. It is easy to calibrate, has good long term
stability and can be interfaced directly with most data
acquisition systems, eliminating the expensive preampli-
fiers required for thermocouples and platinum sensors.
A typical temperature sensor application is shown in
Figure 2. The LM134 operating current at 25癈 is set at
298礎 by the 226& resistor, giving an output of 1礎/癒.
The current flows through the twisted pair sensor leads to
the 10k termination resistor, which converts the current
output to a voltage of 10mV/癒 referred to ground. The
voltage across the 10k resistor will be 2.98V at 25癈, with
a slope of 10mV/癈. The simplest way to convert this
signal to a Centigrade scale is to subtract a constant 2.73V
in software. Alternately, a hardware conversion can be
used, as shown in Figure 3, using an LT1009 as a level
shifter to offset the output to a Centigrade scale.
The resistor (R
SET
) used to set the operating current of the
LM134 in temperature sensing applications should have
low temperature coefficient and good long term stability.
A 30ppm/癈 drift in the resistor will change the slope of the
temperature sensor by 1%, assuming that the resistor is
at the same temperature as the sensor, which is usually the
case since the resistor should be located physically close
to the LM134 to prevent errors due to wire resistance. A
long term shift of 0.3% in the resistor will create a 1癈
temperature error. The long term drift of the LM134 is
typically much better than this, so stable resistors must be
used for best long term performance.
Calibration of the LM134 as a temperature sensor is
extremely easy. Referring to Figure 2, calibration is achieved
by trimming the termination resistor. This theoretically
trims both zero and slope simultaneously for Centigrade
and Fahrenheit applications. The initial errors in the LM134
are directly proportional to absolute temperature, just like
the actual output. This allows the sensor to be trimmed at
any temperature and have the slope error be corrected at
the same time. Residual slope error is typically less than
1% after this single trim is completed.
Figure 2 Kelvin Temperature Sensor
TO DATA
ACQUISITION
SYSTEM
10mV/癒
9.53k
1k
CALIBRATE
134 F02
V
+
V
R
LM234-3
R
SET
226&
I = 1礎/癒
V
S
e 5V
APPLICATIO S I FOR ATIO
U
U
U
相关PDF资料 |
PDF描述 |
|---|---|
| LM334S8#TRPBF | IC CURRENT SOURCE 8SOIC |
| LM334S8#TR | IC CURRENT SOURCE 8SOIC |
| LM334Z | IC CURRENT SOURCE TO92-3 |
| LM334S8#PBF | IC CURRENT SOURCE 8SOIC |
| LM334S8 | IC CURRENT SOURCE 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM335 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:PRECISION TEMPERATURE SENSORS |
| LM3350 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Switched Capacitor Voltage Converter |
| LM3350AM WAF | 制造商:Texas Instruments 功能描述: |
| LM3350MM | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Switched Capacitor Voltage Converter |
| LM3350MM/NOPB | 功能描述:IC REG MULTI CONFIG 50MA 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:3.3V 输入电压:4.5 V ~ 24 V PWM 型:- 频率 - 开关:- 电流 - 输出:125mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 包装:Digi-Reel® 供应商设备封装:SOT-6 其它名称:MAX1836EUT33#TG16DKR |
发布紧急采购，3分钟左右您将得到回复。