- 您现在的位置：买卖IC网 > PDF目录17146 > LM3423MHBKBSTEV/NOPB (National Semiconductor)BOARD EVAL BUCK BOOST LM3423 PDF资料下载
参数资料
| 型号： | LM3423MHBKBSTEV/NOPB |
| 厂商： | National Semiconductor |
| 文件页数： | 25/67页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL BUCK BOOST LM3423 |
| 标准包装： | 1 |
| 系列： | PowerWise® |
| 电流 - 输出 / 通道： | 1A |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 35V |
| 特点： | 可调光 |
| 输入电压： | 4.5 ~ 35 V |
| 已供物品： | 板 |
| 已用 IC / 零件： | LM3423 |
| 其它名称： | LM3423MHBKBSTEV |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页
SNVS574E – JULY 2008 – REVISED MAY 2013
In general, Δ i LED-PP is recommended by manufacturers to be less than 40% of the average LED current (I LED ).
Therefore, for the buck regulator with no output capacitance, Δ i L-PP should also be less than 40% of I LED . For the
boost and buck-boost topologies, Δ i L-PP can be much higher depending on the output capacitance value.
However, Δ i L-PP is suggested to be less than 100% of the average inductor current (I L ) to limit the RMS inductor
current.
L1 is also suggested to have an RMS current rating at least 25% higher than the calculated minimum allowable
RMS inductor current (I L-RMS ).
LED DYNAMIC RESISTANCE
When the load is a string of LEDs, the output load resistance is the LED string dynamic resistance plus R SNS .
LEDs are PN junction diodes, and their dynamic resistance shifts as their forward current changes. Dividing the
forward voltage of a single LED (V LED ) by the forward current (I LED ) leads to an incorrect calculation of the
dynamic resistance of a single LED (r LED ). The result can be 5 to 10 times higher than the true r LED value.
Figure 34. Dynamic Resistance
Obtaining r LED is accomplished by refering to the manufacturer's LED I-V characteristic. It can be calculated as
the slope at the nominal operating point as shown in Figure 34 . For any application with more than 2 series
LEDs, R SNS can be neglected allowing r D to be approximated as the number of LEDs multiplied by r LED .
OUTPUT CAPACITOR
For boost and buck-boost regulators, the output capacitor (C O ) provides energy to the load when the recirculating
diode (D1) is reverse biased during the first switching subinterval. An output capacitor in a buck topology will
simply reduce the LED current ripple ( Δ i LED-PP ) below the inductor current ripple ( Δ i L-PP ). In all cases, C O is sized
to provide a desired Δ i LED-PP . As mentioned in the INDUCTOR section, Δ i LED-PP is recommended by
manufacturers to be less than 40% of the average LED current (I LED-PP ).
C O should be carefully chosen to account for derating due to temperature and operating voltage. It must also
have the necessary RMS current rating. Ceramic capacitors are the best choice due to their high ripple current
rating, long lifetime, and good temperature performance. An X7R dieletric rating is suggested.
INPUT CAPACITORS
The input capacitance (C IN ) provides energy during the discontinuous portions of the switching period. For buck
and buck-boost regulators, C IN provides energy during t ON and during t OFF , the input voltage source charges up
C IN with the average input current (I IN ). For boost regulators, C IN only needs to provide the ripple current due to
the direct connection to the inductor. C IN is selected given the maximum input voltage ripple ( Δ v IN-PP ) which can
be tolerated. Δ v IN-PP is suggested to be less than 10% of the input voltage (V IN ).
An input capacitance at least 100% greater than the calculated C IN value is recommended to account for derating
due to temperature and operating voltage. When PWM dimming, even more capacitance can be helpful to
minimize the large current draw from the input voltage source during the rising transistion of the LED current
waveform.
Copyright ? 2008–2013, Texas Instruments Incorporated
25
Product Folder Links: LM3421 LM3421-Q1 LM3423 LM3423-Q1
相关PDF资料 |
PDF描述 |
|---|---|
| EEM06DRST-S288 | CONN EDGECARD 12POS .156 EXTEND |
| HPL1005-13N | INDUCTOR 13NH 2% 0402 SMD |
| MC33342DR2G | IC CTRLR BATTERY FAST CHRG 8SOIC |
| 18R683C | INDUCTOR RADIAL 68UH 1.35A |
| EEV-FC1C470P | CAP ALUM 47UF 16V 20% SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM3423MHBSTEVAL | 制造商:Texas Instruments 功能描述:N-Channel Controllers For Constant Current LED Drivers Evaluation Board |
| LM3423MHBSTEVAL/NOPB | 功能描述:BOARD EVAL BOOST FOR LM3423 RoHS:是 类别:编程器，开发系统 >> 评估板 - LED 驱动器 系列:PowerWise® 标准包装:1 系列:PowerWise® 电流 - 输出 / 通道:20mA 输出及类型:1，非隔离 输出电压:17V 特点:可调光 输入电压:2.7 ~ 5.5 V 已供物品:板 已用 IC / 零件:LM3508 相关产品:LM3508TLX-ND - IC LED DRVR WHT BCKLGT 9USMDLM3508TLDKR-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLCT-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLTR-ND - IC LED DRVR WHT BCKLGT 9MICROSMD |
| LM3423MHX | 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述: |
| LM3423MHX/NOPB | 功能描述:LED照明驱动器 RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| LM3423Q0 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:N-Channel Controllers for Constant Current LED Drivers |
发布紧急采购，3分钟左右您将得到回复。