- 您现在的位置：买卖IC网 > PDF目录17201 > LM3445-120VFLBK/NOPB (National Semiconductor)BOARD EVAL LED DRIVER LM3445 PDF资料下载
参数资料
| 型号： | LM3445-120VFLBK/NOPB |
| 厂商： | National Semiconductor |
| 文件页数： | 12/40页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL LED DRIVER LM3445 |
| 标准包装： | 1 |
| 系列： | PowerWise® |
| 电流 - 输出 / 通道： | 365mA |
| 输出及类型： | 1，隔离 |
| 输出电压： | 20V |
| 特点： | 可调光，三端双向可控硅 |
| 输入电压： | 90 ~ 135VAC |
| 已供物品： | 板 |
| 已用 IC / 零件： | LM3445 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
SNVS570L – JANUARY 2009 – REVISED MAY 2013
ANGLE DETECT
The Angle Detect circuit uses a comparator with a fixed threshold voltage of 7.21V to monitor the BLDR pin to
determine whether the triac is on or off. The output of the comparator drives the ASNS buffer and also controls
the Bleeder circuit. A 4 μs delay line on the output is used to filter out noise that could be present on this signal.
The output of the Angle Detect circuit is limited to a 0V to 4.0V swing by the buffer and presented to the ASNS
pin. R1 and C3 comprise a low-pass filter with a bandwidth on the order of 1.0Hz.
The Angle Detect circuit and its filter produce a DC level which corresponds to the duty cycle (relative on-time) of
the triac dimmer. As a result, the LM3445 will work equally well with 50Hz or 60Hz line voltages.
BLEEDER
While the BLDR pin is below the 7.21V threshold, the bleeder MOSFET is on to place a small load (230 ? ) on the
series pass regulator. This additional load is necessary to complete the circuit through the triac dimmer so that
the dimmer delay circuit can operate correctly. Above 7.21V, the bleeder resistor is removed to increase
efficiency.
FLTR1 PIN
The FLTR1 pin has two functions. Normally, it is fed by ASNS through filter components R1 and C3 and drives
the dim decoder. However, if the FLTR1 pin is tied above 4.9V (typical), e.g., to VCC, the Ramp Comparator is
DIM DECODER
The ramp generator produces a 5.85 kHz saw tooth wave with a minimum of 1.0V and a maximum of 3.0V. The
filtered ASNS signal enters pin FLTR1 where it is compared against the output of the Ramp Generator.
The output of the ramp comparator will have an on-time which is inversely proportional to the average voltage
level at pin FLTR1. However, since the FLTR1 signal can vary between 0V and 4.0V (the limits of the ASNS pin),
and the Ramp Generator signal only varies between 1.0V and 3.0V, the output of the ramp comparator will be on
continuously for V FLTR1 < 1.0V and off continuously for V FLTR1 > 3.0V. This allows a decoding range from 45° to
135° to provide a 0 – 100% dimming range.
The output of the ramp comparator drives both a common-source N-channel MOSFET through a Schmitt trigger
and the DIM pin (see MASTER/SLAVE OPERATION for further functions of the DIM pin). The MOSFET drain is
pulled up to 750 mV by a 50 k ? resistor.
Since the MOSFET inverts the output of the ramp comparator, the drain voltage of the MOSFET is proportional
to the duty cycle of the line voltage that comes through the triac dimmer. The amplitude of the ramp generator
causes this proportionality to "hard limit" for duty cycles above 75% and below 25%.
The MOSFET drain signal next passes through an RC filter comprised of an internal 370 k ? resistor, and an
external capacitor on pin FLTR2. This forms a second low pass filter to further reduce the ripple in this signal,
which is used as a reference by the PWM comparator. This RC filter is generally set to 10Hz.
The net effect is that the output of the dim decoder is a DC voltage whose amplitude varies from near 0V to 750
mV as the duty cycle of the dimmer varies from 25% to 75%. This corresponds to conduction angles of 45° to
135°, respectively.
The output voltage of the Dim Decoder directly controls the peak current that will be delivered by Q2 during its
on-time. See BUCK CONVERTER for details.
As the triac fires beyond 135°, the DIM decoder no longer controls the dimming. At this point the LEDs will dim
gradually for one of two reasons:
1. The voltage at V BUCK decreases and the buck converter runs out of headroom and causes LED current to
decrease as V BUCK decreases.
2. Minimum on-time is reached which fixes the duty-cycle and therefore reduces the voltage at V BUCK .
The transition from dimming with the DIM decoder to headroom or minimum on-time dimming is seamless. LED
currents from full load to as low as 0.5 mA can be easily achieved.
12
Product Folder Links: LM3445
Copyright ? 2009–2013, Texas Instruments Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| RN-1509S | CONV DC/DC 1.25W 15VIN 09VOUT |
| RO-1224S/HP | CONV DC/DC 1W 12VIN 24VOUT |
| RO-1215S/HP | CONV DC/DC 1W 12VIN 15VOUT |
| RN-1505S | CONV DC/DC 1.25W 15VIN 05VOUT |
| GCC30DCMD-S288 | CONN EDGECARD 60POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM3445-120VSMEV | 制造商:Texas Instruments 功能描述:Evalaution Board For TRIACE Dimmable Offline LED Driver 制造商:Texas Instruments 功能描述:LM3445, LED DRIVER, EVALUATION BOARD 制造商:Texas Instruments 功能描述:EVAL BOARD, LM3445 1A LED DRIVER; Core Chip:LM3445; Topology:Buck (Step Down); No. of Outputs:1; Output Current:1A; Input Voltage Min:8V; Input Voltage Max:12V; Kit Contents:Evaluation Board for LM3445; Input Voltage:8V to 12V |
| LM3445-120VSMEV/NOPB | 功能描述:LED 照明开发工具 LM3445-120VSM EVAL BOARD RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| LM3445-208277EV/NOPB | 功能描述:LED 照明开发工具 LM3445-208277 EVAL BOARD RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| LM3445-220VEVAL/NOPB | 功能描述:BOARD EVAL LM3445 220V RoHS:是 类别:编程器，开发系统 >> 过时/停产零件编号 系列:PowerWise® 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| LM3445-220VEVAL/NOPB | 制造商:Texas Instruments 功能描述:LED Driver Eval. Board |
发布紧急采购，3分钟左右您将得到回复。